pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
Hi all,
I am a beginner with nRF24LE1, when I want to code some examples using GPIOs, I find that it's difficult to understand the PxCON register function. Whether I configure...
I am using the usb port to download an example project to the NRF development kit board, with Keil4. Somehow it keep telling that "No jlink device found", in Keil, the project...
I'm designing my own pcb with a IMU and nRF51422 but i confused,
What's the best choice, LDO, DC-DC or external regulator configuration if I'll use a cell coin?
Someone...
Hi,
We bought new some new nrf51822 beacon boards to get latest revision HW. Then upgraded Keil uVision to latest 5.13 and installed SDK 7.2. However I can't get anything...
I would like to use a network of nine nRF24L01+ nodes {n0, n1, ... n8} in following topology:
n0 has bi-directional links with n1, n2, n3 and n4;
n1 receives from...
Hello,
i'm using nrf51422 with gazell protocol.
Here is my interrupt on success code
void nrf_gzll_device_tx_success(uint32_t pipe, nrf_gzll_device_tx_info_t tx_info...
Hi,
I'm using two STM32F407 discovery kits with one nrf24L01+ module attached to each kit.
Here is my common init code (common for both Tx and Rx):
RF_Init(); /*...
hi:
On ios8 system, sometimes after iphone switch Bluetooth, ancs does not work,
because apple_notification_setup() is not work, but try calling apple_notification_setup...
Hi Nordic DevZone User,
i want to ask if there is a limit of devices which can be found within one scan process?
And how many connections can one master have at the...
We have two nRF51822 chips ("A" and "B") connected via GPIO pins on our board, communicating via UART using the app_uart SDK module (in APP_UART_FLOW_CONTROL_ENABLED mode...
Hi,
I found this (PCA63506) Nordic Board, which I suppose is some kind of audio interface for the Smart Remote 2. However, I am unable to find more information on this...
Q: Is qualification process simplified by some sort of NRF81522+ S110 stack BLE pre-qualification (up to GATT level, what BT SIG ask for BLE devices)?
We use NRF81522 with...
After SD initialization and turning on advertising i have to send large amount of data via SPI continuously. SPI driver code initializes SPI module after SD init and advertising...
Hi,
I have an ISP130301C chip based on the nRF51822 chip.
I'm using the jLink Segger EDU to flash the chip without any problems.
But it seems like nothing is running...
Hi,
I just took a look to nRFgo to see how it generates vendor specific UUID's. It looks if they are generated completely random including the version number. According...
