Hi,
I have question about a project I'm running on nRF connect sdk 2.9.1.
I noticed that whenever an i2c sensor device device_init() is returning a value not equal...
I am trying to run some of the more basic examples included in the nRF Connect SDK on the nRF5340 included in a Thingy:91 X . I have installed the latest version of the nRF...
The OSCILLATORS documentation says:
" The device starts at 64 MHz. For 128 MHz, it must be configured when the CPU starts and before any peripherals that use the high-frequency...
Hello,
I am using nRF54l15 and nRF Connect SDK v2.9.0
I need to know if there is any way to disable the cfg_changed callback at runtime. I want it to be called in case...
I am in the process of getting a Nordic Thingy 91 X up and running for an upcoming development project. However, I’m having some problems getting the Thingy to connect to...
I had to modify the modem_cellular.c file driver in Zephyr to make it work for a SIMCOM modem. I know I could try getting a PR to Zephyr approved but it'll take some time...
Dear Team,
I am experiencing issues updating the firmware image on my custom board based on the nRF7002, using an external SPI NOR flash ( is25lp064 , 8MB). The board...
Hello
I would like to evaluate the module in a place without Cat-M \ NBIoT support
is it possible (for evaluation purposes) to send the data by other means (for example...
Hi,
New to Nordic, new to SEGGER, and new to ARM, so forgive me if I'm just missing something...
I've been asked to write new code for some boards that have the nRF51822...
I am using the SPIM example in the nRF52840 SDK. It uses SPI_INSTANCE 3. I am doing a simple SPI Write of 2 bytes.
I get SS, SCK, working properly. MOSI is transitioning...
I want to take drive code from thingy sdk and apply it to nrf5 sdk uart project, but I don't know how. Please explain in detail because i'm university student ... thank you...
Hi Team Nordic,
I am trying to save my flash data after the DFU process but it keeps on erasing it. I saw a thread in which it was explained to increase the CODE_PAGE_SIZE...
Hello,
I have a problem with app_timer.
My program need to use BLE UART for about 15 second then switch for just RADIO after.
To do so, I enable the ble stack as...
hello support team
nRF52 DK , Mesh 2.01
I am trying Experimental BLE RELAY example.
1. In first trial I am using 1 RELAY DK all works well.
2.In second Trial I am...
Hi everyone, I have a custom board using nRF52832 chip.
I want to turn ON and OFF a LED, which is directly connected to a GPIO pin.
Using this configuration I expect...
Hi,
I want to use the math.h for my nRF9160 project, but when I include it, it doesn't find it. I am a beginner and I wanted to ask how do I include libarys proparly in...
Hi,
I have two nRF54840 DK and I am testing ble_app_att_mtu_throughput example with the boards. I am using nRF5_SDK_15.3.0_59ac345 SDK.
The number on the chip is "N52840...
Hello!
Im getting a hardfault when trying to send 10 bytes data via NUS. I receive the data, but the app crashes:
0> <error> hardfault: HARD FAULT at 0x00000000 0...
Hi everybody. I know that it is complete standart question, which has many asks and solutions here. I'm quite new to bootloader management stuff. So asking about some targeting...
Hi,
I am fairly new to BLE application development on NRF52.
I have a temperature and humidity sensor TH02 and I have interfaced it by making essential changes in TWI...
I found a function, sys_reboot() that apparently reboots the nRF9160. In order to use this function, what must be configured and what are the correct .h files?
Thanks
