Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
I'm trying to pair a Nordic SDK15 central to a non Nordic peripheral ( BLE 4.0)
I have no IO for passkeys
I'm testing by pairing Master control panel ( is it BLE 4.2?...
Hello team,
Having a bit of an issue. The link for the S140 SoftDevice results in an "Access Denied" page.
Origination Page >> https://www.nordicsemi.com/eng/Products...
Hi Everyone
I am able to configure BLE on the template project and it is sending data from nrf52840 to BLE nrfconnect app using the function nrf_ble_data_send() .
However...
HI All,
I am trying to upgrade sdk v11 to sdk v13 in my project and after compilation i am facing Linker Error as mentioned below.
binaries/app/SmartTag2/dfuFlash.c.o...
Hi :
I have the same problem. I try to flash program to the Dongle using MCP. Every time I program the Dongle, the MCP log report: "NO response from master emulator". What...
Hi all,
I am using SDK version 15, SES IDE.
I am working on Dust sensor, for that i am using SAAADC example code, I want to read the ADC value from the pin, like this...
Hi Sir,
Based on the nRF5-SDK-for-Mesh , it mentions " release with a Bluetooth mesh profile v1.0 qualified stack".
Do we already have the QDID information for Mesh profile...
Hello,
Can i implement same functionality provided by NXP Mifare DESFire EV1 to nRF52832?
If yes, where i get the details and reference code for the same.
I want...
Hi Sir
I tested the cli example or uart example of SDK15, the uart response data are wrong and slowly.
I have no idea what happened. please help.
------------------...
I am currently using mesh sdk 2.0.1 and I plan to migrate to 2.1.1. I saw this while comparing the light_switch example of the two sdks.
proxy server is not supported...
I am using nrf52832, and used mpu 9250. I want to store the data of mpu 9250 in external and internal flash memory. will you help me how to do this?
the odr of sensor is...
Hi,
I am developing an application using the nRF52840 as NCP with a raspberry pi as the primary processor, using wpantund. I have 3 devices (3 raspberry, each with its own...
In most of the examples the FIRST_CONN_PARAMS_UPDATE_DELAY define is set to something like 5000ms. Is there a reason it needs to be that long? I would like to switch to a...
