SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
Hello, as the title suggests. I'm just wondering if the nRF91 (nRF9160 or nRF9151 DK) can use vanilla Zephyr instead of NCS for getting GNSS data (using the GNSS API)?
I...
I am using a STM32 with the NPMX drivers.
I am having a few issues and wanted to see if there are recommendations.
Issue 1:
disabling the interrupts does not seem...
Dear Nordic Community, I want to build samples/basic/blinkly on nordic nrf52840_dongle inside my Zephyr workspace. I use Zephyr 4.2.0, but on Zephyr 4.3.0 I have similar problems...
Hello, I am looking at pages 871 and 872 of the datasheet for the QFN48 package, but I’m not sure I understand correctly. Could you please tell me which GPIO P0 pins can be...
I’m using an nRF54L15 evaluation board obtained from a distributor and currently testing transmission and reception of large data chunks. Everything was working fine until...
I have an external device. After connecting it to the central device, I found that the Bluetooth service of my external device couldn't be enabled properly. When I checked...
Hi, I have the radio_test example running correctly on a nrf52840 dev board. I am able to use the Nordic Serial Terminal (v1.6.0) to send commands and read responses.
...
I am developing a custom board using nrf54l10 chip. So far, I have been able to use a code to comunicate through spi and uart for me to use printk function.
Now I was trying...
The docs( docs.nordicsemi.com/.../dect.html say that th nRF9151 modem can't do GPS/LTE and DECT NR+ at the same. Could the modem switch between the two operation modes while...
Hello team,
I am using SPI00 of NRF54L15 to communicate with w25q32fv (spi Flash). Below is the configuration I set in .overlay file
And below is the code I am using...
Hi,
I have a question about the the fields " tod_toa_reflector" and "toa_tod_initiator" in struct bt_hci_le_cs_step_data_mode_1.
I understand that these values represent...
The e-mail contains news of a new use of the nRF9151 module but uses the word "proves" and as an English language Cambridge qualified teacher I must mention that the word...
Issue description
I am using SAADC in single-ended mode with 3 channels (0/1/2). Measurements are performed by enabling SAADC, running offset calibration, configuring the...
Hello,
I have an application running on legacy NRF SDK and using the nRF5 bootloader, which has below flash sectors, 0x00000 - 0x026000 - Soft-device section 0x26000 - 0x0D9000...
