Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hi everybody,
I have developed a project where a central device with multilink, connected to the maximum peripheral as much as is possible (in my case 4 devices more). ...
Hello,
I'm trying to figure out how to get A-GPS data via a GSM modem in places where LTE-M is not availalble.
Does the SUPL library support this, if I populate supl_client_ctx...
Hello all,
I just found out that the nRF Connect extension for VSCode has been release, which is great news. Good job Nordic Team! I have followed the steps described in...
Hi, dear Nordic.
I'm using BC805M Module which uses nRF52805 SoC. What's the max sink/source current for individual pin OR total chip, please? Where could I find relative...
Hi,
Im using nrf9160 based custom board, nrf sdk 1.5.1.
I want to get the time from NTP servers, for that i connected to CATM1 n/w, connected to NTP server using UDP Protocol...
Hello, I am working with custom board nrf52840 and SDK 17. I am doing some changes to the project and I am getting an error that the SDK is using VFP register arguments but...
Hi,
I am getting this error message when using the nRF52 dev board but not when using the nRF51 dongle. I receive few packets and then it disconnects with this error message...
For example, I'd like to add library at_cmd_parser to my project. (It's under /ncs/nrf/lib/at_cmd_parser.)
My project is out-of-tree in its own directory. I tried in CMakeLists...
Does unblocked saadc sample the buffer size and stop or does it start re-sampling after the callback? In other words, if the buffer is 100 entries in length, will it issue...
I was able to write some I2C code to successfully work with the TCS34725 by porting a library from Arduino without fully understanding what was going on. Now I have to port...
Hello,
I am using th PCA10040 board, and I can build my project without problems. But when I debug it, 'stopped by vector catch' error appears. I have been reading possible...
hello Nordic
i am working with nrf52840, with zephyr (i am new to zephyr)
i have an issue with not responding pin interrupt so i try to run zephyr example to see how...
nRF9160 DK NCS v1.6.0, SLM with:
CONFIG_SLM_GPIO_WAKEUP =y
CONFIG_SLM_INTERFACE_PIN =24
Sometimes after at#xsleep=0 and several pulses on pin 24 SLM wakeups with...
Hi. I'm testing the multi-image DFU in nRF Connect SDK 1.7.0. I'm seeing an issue with the firmware images not getting reverted when it should.
Here's what I'm doing:
...
