In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
This link in nordic nrf connect apps is old version. There is no enable services for now. It should be changed to enable CCCDs. After enable it , data will be received in...
I tested the NFC transceiver APDU of the project nfc_uart is good. Then I ported the NFC code to the project ble_app_uart. When the board is simulated, the program pointer...
Hi,
I can use the SPI master functionality within nrf_drv_spi.c/.h just fine (i.e. calls from main) until I connect to my nRF52840 and utilize NUS. If I try to issue a nrf_drv_spi_transfer...
Hello,
I am working to implement the BLE stack for a HID keyboard, borrowing/based off the supplied example "ble_peripheral/ble_app_hids_keyboard".
Stack initialization...
In SEGGER Embedded Studio I am not able to connect to the J-Link anymore.
The error message says No idcode detected.
The J-Link commander program returns the following...
The SysTick port for NRF52 does not support tickless idle on freeRTOS, what is the reason for this limitation? Are there any known problems behind this limitation?
I tested the code below to make the board go to sleep and wake up on each button press. When I start, it draws 30ua, but when I press the button it shoots up to 200ua (a clear...
Hi,
We are developing nrf9160 sensor based product powered by primary battery(non rechargeable). Sensor current consumption is less than 1 mA.
while trying Saft LS14500...
Hello,
How can i put out the received Adv Data on the UART? Currently I get for every advertise packet the BLE_GAP_EVT_ADV_REPORT in my ble_stack_handler. Then i wanted...
I'm using the ble_app_hrs example code and added a new custom services with multiple characteristics . conn.interval 10ms- 15ms and need to get maximum throughput so i set...
I have nRF52840 DK (board PCA10056) . Right now I flashed LED blinking program on nRF52840 DK. It is fine.
Now I want do ADC operation, so I fed some external analog signals...
Hello, I am trying to send and recieve data with the M24C32-FMN6TP 32 Kbit (4K x 8bit) eeprom. My data are arrays with 16bit values and the datasheet says it cannot write...
Hi,
I have nrf9160 dev board.
It seems to me that getaddrinfo() has memory leak. If socket is closed, and call getaddrinfo() to reopen, it returns -10 (memory) error....
i'm looking for support in desinging modules working in zigbee network with driving this network from mobile phone by bluetooth. It has to be multiprotocol system. How should...
