I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
I see LESC_DEBUG_MODE defined in some of the examples in the SDK (17.0.2) but I can't see where this definition is referred to in any of the libraries, so I don't think it...
I am facing strange issue when I execute firmware with NRF_LOG_ENABLED set to 0.
During BLE communication, Firmware is crashing.
If I enable NRF_LOG_ENABLED, all is working...
My requirement program flow is clearly written down .Please help me out.
void USART_EVENT_Handler()
{
// disable timer 1
//disable timer 2
// clear timer 1 count...
HI,
I have already got output from each of the SHT20 and MLX90614 sensors. Now I want to combine both the code. Regards, I need an help to Setup prj.conf file
Thanks &...
I'm referring to the HID keyboard example (BLE peripherals)
The example itself is more or less working and since my goal is to send a whole character string via BLE and...
Hello, Nordic!
When a scan is started with certain scan parameters, a timeout event (NRF_BLE_SCAN_EVT_SCAN_TIMEOUT) will occur in a time less than the specified timeout...
How can I do a point multiplication in NRF52840 using the ECC hardware accelerator for the secp256k1 curve? Also are there examples or any documentation on how to implement...
Hi,
I'm openning a new case (following the proposal of Einar Thorsrud ).
I want to do a BLE NUS project with custom service 128bits and with custom characteristics also...
Greetings!
Using the NRF52840 PDK, I succesfully erase, write and read without any modifications!
I have custom boards which involved a NRF52840 and a MX25R6435F (so same...
Dear Nordic Support,
My project is split into two parts: A firmware application that is based on the Generic Level Server model example (from the Mesh SDK) and an Android...
Good morning,
I'm working on nRF5 SDK v17.0.2 and I am using Segger Embedded Studios (SES) for the development.
I'm having a problem when I want to share my project...
I'm aware that the nRF CLI tools are not yet ported to AArch64 so they don't work natively on Apple Silicon. Normally rosetta 2 is fine, but nrfjprog is not compatible with...
working with nrf52832, sdk 16.0 s132 v7.01
in the uart example i get to this place in the code :
i get a pin toggle which makes my system do some unwanted things...
Hi,
I have a ARM based Linux host CPU connect to MDBT42Q-U(nRF52832).
But I cannot control it by BlueZ:
```
root@OpenWrt:/# btattach -B /dev/ttyMSM1 -P h4 & root...
