Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
I am using the nrf52833 with 17.1 SDK and s140_nrf52_7.2.0_softdevice，i want to scan a scannable extend adv packets，
This is what i get in the BLE_GAP_EVT_ADV_REPORT ： ...
# Background
I am attempting to install ble-sniffer onto WireShark for BLE sniffing. I have been following the guide in Link. I have already flashed my nRF52840 USB dongle...
Using Thingy:53, I needed to add the following code to the boards/thingy53_nrf5340_cpuapp_ns.overlay file in order to be able to view the output:
&uart0 {
status="okay...
Hi
We measure I2C SCL falling time is 5.87ns, little faster than spec. 6.54ns ( 20*1.8/5.5)
We use PIN_CNF[n] (Address offset: 0x200 + (n × 0x4)) ID D drive to tune, but...
Hello,
Are there schematics available for the nRF9151DK?
In the hardware ZIP file, I can only find the BOM and PCB files (PcbDoc and PrjPCB), but no schematic files or...
We are trying to understand whether it is possible to use our external flash drive at45db641e to implement DFU and then load the application firmware via Bluetooth. As far...
I want to design a pair of TWS speakers using the nRF5340, but I'm having a hard time figuring out where to start. From what I understand, the unicast server nRF5340 audio...
Hello Nordic Team, I have devices running nRF9160, modem firmware 1.3.6, tied with MNVO SIM card that provide access to multiple operators. Providing an example seems to be...
Hello Nordic Team,
We are working with the NRF5340-QKAA-R7 and need clarification on which physical pins can be used for UART, I2C, SPI, PDM and USB interfaces .
We have...
Hello, I observed that under low-throughput conditions (2 kbps), the power consumption of the nRF21540 combined with the 54L15 (at 20 dBm) is actually lower than that of using...
Using the Zephyr HCI_UART sample, configured and built for an nrf54L15 DK, with version 3.2.1 of the SDK, I get an HCI error 7 (Memory Capacity Exceeded) when attempting to...
Hello Nordic Team,
We are working with the NRF5340-QKAA-R7 and need clarification on which physical pins can be used for UART, I2C, SPI, PDM and USB interfaces .
We have...
Hi，
During the initial screening of Matter certification during the R&D phase, it was found that several test items did not pass the test. Could you please help investigate...
