I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hi, I am using the Nordic nRF53DK, with the Segger IDE, in the NCS 1.5.0 release.
I'm playing around the Data Length Extension with the Sample of the Central UART...
Hello, My environment is nrf SDK v1.5.1. The board im developing for is the nRF52840DK. I'm trying to do some ECP-Calculations and therefore Ii want to use some function located...
Hello, All
I want to implement OTA using Thread with nRF Connect SDK.
Is there any sample code or reference this can be done with Thread?
Even if there is any experimental...
Hello,
I have a: nRF5340DK connected to Windows10 PC via USB.
I also have these that are working fine in terms of being able to communicate with the nRF5340DK over Bluetooth...
nRF SDK version is 1.5.1
upgrade modem fw to 1.3.0
Is there any way to do software reset on GPS modem? I have ran the gps example and I notice that "printk" sends everything...
I'm using the nRF5340 DK with the HRM example. My phone is HUAWEI mate 10 (Android 10).
I could scan the Zephyr Heartrate Sensor in nRF Connect App and nRF Toolbox App ...
Hi Team,
In continuation with Case ID: 269054, 269278
I am using NCS (as suggested) to avoid high current consumption happening during softdevice initialization.
I set...
Hi, I'm enthusiast of nrf5340 DK. BUT: in the samples I'm not able to find some viable openamp (other ipc seems to have the same problem) example. I am looking for a way to...
To the kind Nordic support team,
I have got a nRF52833 based Raytac module I'm using to develop before using a custom board.
I'm using Microsoft Bluetooth Virtual Sniffer...
Dear Hardware Application Engineer,
We are using nRF ASICs for our IoT products for the past two years.
In nRF52x series products, forex. nRF52840, there is a power supply...
When I do a DFU on my device (nrf52832 with Zephyr) using nrfConnect, the update is successful, but I get a message in the log stating "Length of data to send exceeds MTU...
Hi Nordic,
I am using the Raytac module with the nrf52840 inside, I have set my hardware as mode of Reg0 DC/DC enabled. Which disconnected the VDD and VDDH. Also I have...
Hello,
We need to use the RX TX on TTL level. That is possible with the nRF24L02 chip, as fa as I can understand from the datasheet. But we also need to use 8 bits, even...
Hello,
I am using nrf52840(nRF5 SDK v15.2.0). armgcc compiler, softdevice s140 hex, and application + OTA bootloader combined hex file.
in my application, I have some...
