Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
Hello,
I recently purchased a Nordic Thingy 91 device, and I have been working on it for a few weeks. I am currently experiencing two major issues with the kit that are...
Hi,
I have a board which is nrf9151 with nrf52840 as BLE controller connected via hci_lpuart. This works fine so far, I am able to do simple AT commands as well as doing...
when I try to add a build config, i can only see a blank page for build configs.
but if i click on another project's build config which is already created, i can see the...
Hi,
I'm troubling using the retention module of Zephyr with NCS 2.6.1 on an NRF52840. I've read the Retention System Documentation of Zephyr but it is not working for me...
Folks,
Am running VSC 1.95.1 on Mageia Linux.
I have a 52833 board that I have working in that I can write to and read from custom BLE characteristics and send data out...
Hi
I'm setting up an OpenThread network and am trying to use the nRF Thread Topology Monitor to visualize the network for debugging purposes. However, no OT devices appear...
According the AT command documentation, reading the device certificate is not supported.
That's somehow irritating. There is no reason for that, at least for those who common...
Hello,
My board contains nRF9160 and nRF52840. The nRF52840 is a HCI controller (based on HCI lpuart example). nRF9160 communicates with nRF52840 over UART. I want to perform...
Hi, in our project we use nRF5340 to control some externanal peripherals as flash mem through SPI and also we need BLE comunication.
The case is if whe allow the config...
Hi, I am trying to use the DECT NR+ sample from the 2.7.0 nrfconnect sdk but I can't seem to get the following to work in the prj.conf:
the results of my build give...
Is there a way to convert the firmware for the nRF Connect RSSI viewer to work on the nRF21540DK. I imagine it isn't too difficult, since it is essentially the nrf53840 but...
I have customed a board based on nrf54l15.
Then I built the matter light_buld demo with target 'nrf54l15pdk_nrf54l15_cpuapp' and burned the file "merged.hex" into my custom...
Hello,
I'm using "Bluetooth Mesh Light switch" code which i have modified to act as a gateway. Where it periodically collects data from lights. After receiving data from...
Can the VDD PIN of 4L15 be used to detect the ADC voltage? VDD is powered by a dry battery (3.2V~1.8V), LED+ is powered by 3.3V, LED- will be connected to the I/O of the 54L15...
