I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
I am working on project in which i want to read data from sd card and send it to mobile through BLE , I am using ble_nus_send to send data but when i decrease the delay then...
Hello,
Using sd_ble_gap_adv_set_configure() with ble_gap_adv_params_t I observe that the actual time when the BLE_GAP_EVT_ADV_SET_TERMINATED event is raised is earlier to...
Hi All,
Likely because I am still quite new to this, but I have started with MQTT simple example and whenever I do use GuiConfig to make mods, it saves them to
proj/build...
The disccussion here
https://devzone.nordicsemi.com/f/nordic-q-a/24592/my-nrf52-nrf51-dk-kit-doesn-t-work
has been closed.
I followed step 4 and it took a few tries...
Hi,
I use a Segger JLink EDU (the big version, not the mini) to flash some custom boards. This used to work fine until I upgraded nRF Connect and got Programmer v2.0.
...
Dear sir/madame,
By an accident I selected Power Profiler Kit II when I wanted to download an application to “PCA10056 DK” . After that ‘download’ Power Profiler Kit II...
Hello,
I'm using NRF52832 as a controller for cellular modem and used the AWS IOT supplied with the NRF Connect SDK.
I want to use the AWS FOTA and I'm a bit lost, I added...
This builds on a previous Forum Post that was closed out.
There is a peculiar issue with the NRF52840 SAADC sampling. For an unknown reason, triggering the SAMPLE Task in...
I have a nRF5340 with a UART that connects to a circuit that is not powered on until it is needed by the application. So the UART must be powered off until the application...
Hi,
We are developing cycling trainer, so we use BLE fitness machine profile. Our functions are basically completed and we are testing with some VR cycling windows or desktop...
Hello, please help if you can.
Once connected. I am asked to program the board when trying to use BLE from nerf connect.
However, I get the error: Error while setting...
Hi All,
According to the title,how should i do?
I want the project on the left to have a dependencies under main like the project on the right.
Best regards,
...
Hi all,
Currently working on a project using the nRF52DK and nRF52832 that will be powered by a CR2032 coin cell battery.
I want to measure the battery level from the...
Hello.
I'm working with nrf52833 custom board and S113 softdevice for Buttonless DFU.
The pieces of information below are my FLASH & RAM address settings.
(Reference...
I'm trying to duplicate the boot behavior of a Thingy91 on a custom board, i.e. SW4:BOOT and SW3:BUTTON on power up, but the switches available use different IO. I'm wondering...
