Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello all!
How can I get the current count of a timer without stopping it?
Right now I'm doing like this:
_timer_base->TASKS_CAPTURE[channel] = 1; uint32_t counter...
Hi,
I am no programmer, but I wanted to try the Wake-on-NFC example on the 52840 dongle (I soldered an NFC flex on pins P0.09 and P0.10). I have downloaded SES and nRF SDK...
I want to connect heart rate sensor and bike power sensor together. I config channel 0 for heart rate sensor,and channel 1 for bike power sensor. Ant work well when both sensors...
I've just tried to compile and run the stock lpcomp example on two different computers, targetting an off-the-shelf 52840 dev board. It compiles, and starts fine, but doesn...
Hello,
I am creating an application that counts the number of times the button is pressed (Every high to low transition).
I am using GPIOTE to sense the high-to-low events...
Hello,
I am considering redistributing the SDK source code. I also saw the following, but hasn't it changed?
devzone.nordicsemi.com/.../32969
【SDK：15.3】
Hi,
How can I understand what all Errata's are applicable to softdevice and are taken care of?
For my application I am aware of the modules/peripherals being used and...
Hi,
I noticed there is no SWO support mentioned in Product Specification 1.1 for nRF9160. But since the architecture seems similar to the nRF52/nRF53 that have SWO under...
I have been interfacing with the Macronix external flash via the nfrx_qspi library for logging. While I am able to use nrfx_qspi_read() to obtain my log data, I am also able...
PM_MCUBOOT_STORAGE_ADDRESS and PM_MCUBOOT_STORAGE_ID seem to be no longer defined as of SDK1.2. As per the discussion here , I tried using DT_FLASH_AREA_STORAGE_OFFSET which...
Using nRF52811, Segger SES, and SDK 16.0, I have some times that seem to be off by ~2X.
I'm timing by setting a gpio before and after the event and capturing with a scope...
Hi
Referring to
https://devzone.nordicsemi.com/f/nordic-q-a/58652/additional-questions-to-nrf52832-errata-220-clearification/238659#238659
From the above post, the...
I am new to the nRF9160dk board. I have been able to compile and run some of the sample programs. I am now looking to have a simple program to talk to external uarts 0 and...
I need my sara sara-r410m-02b ublox module to connect to the cellular network using at commands. For this reason I require to send the commands by means of programming lines...
