Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, our entire code base is built around the Nordic SDK. We are considering designing a system that uses an nRF52840 as its controller but has no wireless functionality...
Setup: The nRF52840 DK is running the peripheral_hids_keyboard sample project. The device is connected to a macOS host, showing expected functionality.
Problem: When the...
Hi, We are using an nRF5340 and nRF Connect SDK v2.6.2. We have set CONFIG_BT_BUF_ACL_RX_SIZE to more than 251 and BT_CTLR_DATA_LENGTH_MAX to 251 in our prj.conf.
W hen...
my program works on the nrf52840 DK but does not work on the custom board using nrf52840-QFAA. We are using nrf sdk V2.8.0 running zephyr. Program is attached.
What to do...
Hello,
Version - nrf Connect SDK v2.7.0
The background to the system I am developing is described here and here
In short, I have an application containing a BLE Peripheral...
Hello everyone, I hope you have a good days. I'm developing an project for military standards. I'm using Nexys 4 DDR FPGA ev. board and VHDL language. My question is how can...
NCS 2.6.0, nrf52840
On our board we have attached a QSPI nor-flash as well as a SPI-based OLED display on the same pins.
I'm wondering if there has been any attempt...
In my application, I have implemented Serial Recovery. The interface used for the transfer is UART0 , which I also use in my application at a baud rate of 1M. When I enter...
I'm struggling to get a peripheral device to work with two simultaneous connections. I have attached my configuration (for the application) and my connect/disconnect callbacks...
Good morning team,
As the nRF7002 has been certified Wi-Fi 6 and registered by the Wi-Fi Alliance, can devices embedding the nRF7002 use the Wi-Fi logo and the Wi-Fi designation...
Good morning Nordic support,
I'm a beginner with the nRF Connect SDK and the nRF5340 microcontroller.
I'm using SDK v2.9.0 (the latest available for my Mac).
I started...
Hi, I have been trying to understand how to modify existing projects/samples by adding aspect that are already supported in the libraries. I have an nrf9151 development kit...
Hi,
I'm working with a company that is writing an app on both android phones/tablets and chromebooks. I'm making a new bluetooth device for them, but also helping with...
I'm using a nRF54L15-DK, going through lesson 9 of the intermediate tutorials, using the ncs-inter files at commit 2475c72: Update mcuboot.conf · NordicDeveloperAcademy/ncs...
Hello,
I've been working on a project that uses an nRF52832 to send data over bluetooth. I'm sending large chunks of data, and I'm wondering what the best way to view this...
