Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
I am evaluating a front end module by skyworks 66111 output power is ~14dBm. The FEM requires that logic dictate when to transmit and when to receive. When CRX, pin 17, is...
HI
we have developed our custom board using nrf5340. We are using NCS v1.7.1 for application development. I can't able to flash the HCI_rpmsg application to the network...
Dear Sir or Madam,
I would like to establish Bluetooth communication. When the Central is connected to the Peripheral, I want to measure the RSSI value of each data channel...
I wanted to add this info to my previous ticket, but there was no option to reply. Just an FYI, here is the link:
https://devzone.nordicsemi.com/f/nordic-q-a/84225/expert...
I have the following: - NRF52840 - BG96 modem - NCS 1.5.1 - Zephyr v2.4.99-ncs2
When I start the firmware, it will first bootstrap followed by leshan server registration...
There already exists a question in the DevZone regarding this error but a lot of time has passed and maybe there is already a solution out there.
Basically, I want to execute...
Hello I have been able to run the lvgl sample in the nrf9160dk, however this only works when built in a secure board, when build in non secure a bus fault occurs. Using the...
All of our wireless products over the past 10 years have used the nRF24L01 or nRF24L01+. In order to minimize latency for our time-critical communications protocol, we are...
Hello,
I am trying to program an nRF9160 chip using pynrfjprog v10.15.2 and JLinkARM.dll version: 6.88 with a Segger Flasher Compact. This flasher supportd the nRF9160...
Hi,
I need to know on how to work with asynchronous SPI for my application use case evaluation, However i found no sample/example projects demonstrating the use of nCS...
Would it be possible to know a little bit more about the onboard integrated RF52-DK Nordic Board Antenna please? What type of implementation is used?
Kind Regards,
Za...
There is another case, where someone else pointed out the same issue but I can not find it. Anyway there was no solution.
When using VSCode with NRF Connect SDK installed...
Hi
can you help with this? Setup: MoSh example running on nRF9160DK
There appears to be some sporadic «Old AT event handler : %CESQ xx,y,zz,n » notifications with the...
Hi, I am working with the Thingy91 development board. Currently, I have flashed SLM on nRF91 and I am using nrf52 as my "main" processor for sending at commands to nrf91....
