How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hi,
What we are currently using is nRF52832, the central product is SDK16, and the peripheral product is SDK13.
Does SDK17 only support BLE Secure Mode 1 Level 4?
Are...
Hello. At first I m newbie and don't have experience with Thingy:52 and Embedded Segger Studio for ARM.
I m trying to work with my Thingy with Segger j link and SEGGER embedded...
I am trying to build the zephyr blink project using west :
I have installed the gnu-arm-embedded toolchain and set my environment variables accordingly : ZEPHYR_TOOLCHAIN_VARIANT...
Hello
The Uart Baudrate is initiliazed at 115200 baud but i the BLE nRF52833 is sending with about 115900.
I try to switch to hf clock but the baudrate is to high.
...
Hey,
I have a nRF central that connects and bonds to peripheral devices via BLE.
From what I understand, the peripheral device has a BLE MAC address that isn't consistent...
I am setting to NRF_SDH_BLE_CENTRAL_LINK_COUNT=1 ,it is working fine for ( 1 central and 1 peripheral )connection is fine(data also sending),but i am changed to NRF_SDH_BLE_CENTRAL_LINK_COUNT...
Hi
I am new to Nordic
I am using nordic nrf52832 with segger embedded software tool woth nordic support version NRF SDK 16.0.0
I am facing issue with build configutations...
Hello.
I would like to get an event that an advertised packet has been sent in a peripheral device. Is there a way to do this? Also, is it possible to get the channel used...
I'm using nRF9160DK and in that cJSON formation give me some error because of that my device will restart again and again
as in code if I'm input cJSON_AddNumberToObject...
Using SEGGER embedded studio for ARM (Nordic Edition) v5.60. using Project-> Configure nRF Connect SDK Project Fails in configuring MCUBoot in Zephyr.
No Documentation on...
i am working on power measurement of ble. i want to change ble connection interval in nrf blinky code say to 100ms, 200ms, 1000ms. how to achieve this and
what is the use...
I"m using SLM from NCS 1.6.1.
I'm testing HTTPCREQ with HTTPC port 443 and security tag = 1. After I reset SLM, my send is successful and passes server validation checks...
I have been using the DFU on nRF5 SDK for some years now and we use this feature to update firmware in the field.
I have sucessfully managed to get the SMP Server sample...
