How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
THis may have an obvious answer to an experienced embedded programmer but I do not qualify to be that. So I have a piece of working code that runs on the nRF52840 DK and it...
Can you use/link both nfc T4T and T2T libraries and wrapper/driver source in same application/build?
I don't mean emulating both modes at the same time.
Thanks.
To the kind attention of Nordic support team,
I have been using nRF ble sniffer successfully, it is a great tool. But I have some troubles when it comes to use it for ble...
Hi there!
I am placing variables in the ".non_init" section so that their values are retained across software resets. This works great if I only use an App + Soft Device...
I want to modify the uuid through the serial port. What variables can I use to describe this define? Is there any code for reference ?
#define BLE_UUID_NUS_TX_CHARACTERISTIC...
Hi there
I'm currently using three different target platforms/boards #1 : a Nordic PCA10040 - attached to USB #2 : a UTO-NBL-52A developer board - attached to a J-Link plus...
Provisioner and client (provisionee) roles in the same application.
Hello everyone,
First, I am using SDK 17.02 and BLE Mesh 5.0.
By the moment, I want to integrate...
Hello,
I want to realize the data receiving and sending function,so I adapt the transmitter demo in '\nRF5_SDK_16.0.0_98a08e2\examples\peripheral\radio\',and my code is...
Hi all,
we are trying to connect 20 peripherals to one nRF52840 master (connected to a Laptop running a python app with pc-ble-driver-py) and transmit about 1000 Bytes per...
Hi guys,
I have a custom board containing a Raytac nRf52840 module running the Arduino core. The Arduino core configures the nRf52 to expect a 32K crystal on the xtal input...
Hello
I Just got my first Custom PCB's i dont know how to compile the code into them .Can someone help me . I just get the errror messege when i try to find target :
Failed...
Hello, I am using SDK 16.0 and mesh SDK 4.2.
We successfully implemented remote provisioning capabilities in our devices' firmware. One thing we are noticing though is that...
Hi,
I am using spis example from "SDK v17.0.2" with slight modification in the code as given below
On the Master end CS pin is pulled low and send 1 byte(0x45) only...
Hello,
I'm using nrf52840 with gcc compiler and SDK15.3. For our firmware update procedure, we use two flash storage instances. One for the transmitted new application and...
Nordic：
We need to do a communication certification, we need NORDIC to provide S112V6.1.1 QDID: 125078 certification report certificate。
thinks
jermi.jin
2021.061...
