Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I am trying to run the BLE Thread Dynamic Template example on a nRF52840 dongle. I'm using Segger Embedded Studio to generate an hex file. I flash the hex file to...
Hello,
During testing we found that whenever in system off mode, the CPU wakes from VBUS rising. As expected. We then do a vibration to notify the user the USB cable was...
When integrating nRF Mesh SDK 4.1 with nRF SDK 16 I got an error in runtime.
The call sequence:
mesh_init() -> mesh_stack_init() -> nrf_mesh_init() -> mesh_config_init...
Hi all,
I have really strange behavior with Sesgger SES. I'm working on Linux Kubuntu lastest version.
Segger version is :
SEGGER Embedded Studio for ARM
Release 4...
I am trying to use C++ with an nRF5 board, but I'm running into issues with the MDK, IAR (v8.40.2), and C++. When I try to include "nrfx_gpiote.h" in a .cpp file, I get the...
Hi,
I have a basic setup consisting of a time-slotted transmitter and receiver so that I can experiment with the raw coded and uncoded modes, exploring all the NRF_RADIO...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hi, I want to create a mesh network with two nrf52840 dongles. To programming them I used the light-switch example from SDK Mesh v4.0.0 following the steps in this tutorial...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
When I connect to nRF52810 with RTT viewer and then unplug J-Link probe from the device without properly closing the connection in RTT viewer, the current consumption in deep...
Hi everyone,
I want to measure the total execution time of saadc_sample() & saadc_callback() functions. I am using the application timer and I have inserted the app_timer_cnt_get...
Hi everybody, I am a beginner and I need your advice to start to modify the example of Radio Receiver/Transmitter. Ultimately my goal is to measure the time between the reception...
Error message from KEIL CMSIS D/L :
Update available for ARM::CMSIS (installed: 5.6.0, available: 5.7.0) Update available for ARM::CMSIS-Driver (installed: 2.5.0, available...
I have developed an bootloader operating with external flash for image storage. For the use case it is not acceptable to put the device into an inoperable (no-application...
