I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
Hello there,
I am working in my master degree project with nordic NRF51822 microcontroller, but I faced two problems. I don't know if is a SD problem or hardware problem...
I've been tested for BT SIG however have met error which sent 0xc000 and got 0xc000. I expected to receive 0x8xxx. Command is LE_TEST_END in DTM.
I tested with nRF52832...
Hi!
I have old code written in nRF51 enviorment with SDK nRF5_SDK_12.0.0.
I've successfully flashed the softDevice (s130_nrf51_2.0.1_softdevice.hex).
No error occurs...
hi, I am fresher starting my carrier in ASIC i am learning about UART where i come across with the word "DEADBEEF" in the coding please help me with where it is used and how...
Hi We've been using SDK12.1 with softdevice 3.1.0 on a NRF52832 for some time now. Now we want to upgrade our SDK to 15.2 with softdevice 6.1.0. We've converted the application...
Hi all,
I am working on nRF52840, nRF5_SDK_15.2.0, pca10056,usbd_cdc_acm
I can now communicate nrf52840 with PC,However, I failed to connect nrf52840 to android, Android...
Dear Team,
Greetings !!!
Device - nRF52832 Softdevice - s132_nrf52_6.0.0 IDE - segger embedded studio Bootloader - secure bootloader
In our current application, We are...
Hi,
We have build complex application based on Nordic SDK. Right now we are thinking about moving to Zephyr OS. I was wondering if there is any tutorial/tips I can find...
Hi, I'm using nrf52832 development board. In which i have flashed hci_uart example code of zephyr (latest code taken from https://github.com/zephyrproject-rtos/zephyr ) which...
Hello,
Our product is configured to use 3 total GPIOTE channels –– 2 sensors configured for "high accuracy" GPIOTE events, each around 10Hz refresh rate, and 1 using "low...
Current consumption during k_cpu_idle() after GPIO interrupt does not take the same value. Why does this happen? Any idea? Thank you for reading this post in advance.
<Environment...
hi all, i'm using uart with easyDMA, and i'm disabling and enabling it back on my code. before disabling the uart TX and RX works fine. after disable&enable i get wrong data...
Hello,
as part of the development that will soon be in production, I would need to be able to authorize or not the pairing according to an internal state of my device. ...
The memory returned by the pointer returned from cJSON_PrintUnformatted() in below file must be freed.
https://github.com/NordicPlayground/fw-nrfconnect-nrf/blob/master...
I m analysing application source code searching for implementation of INDENTIFY.
The problem is that application has hundrets of classes and it is very complex so it is...