if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hello Team,
I just recently purchased Thingy52 i was wondering i can use NFC NDEF update using python library if it is possible can you point me to right
documentation...
Hello!
I am working on firmware for device that has freertos in the base and implements BLE beacon and 1 service with 7 characteristics. Everything works. But power consumption...
Hi,
We are currently testing DFU upgrades on Android. In my current setup I have two different phones, a Sony one running Android 8 and a OnePlus running Android 10.
The...
We have a device (in central mode) initiating a secure connection to a peripheral (slave) via the usage of `pm_conn_secure(conn_handle, false)`. This results in a `PM_EVT_CONN_SEC_SUCCEEDED...
Hi All,
I want to convert analog input into digital using SAADC on nRF52840 DK. After that to push the SAADC output through the Bluetooth (nRF connect bluetooth mobile application...
Hi，
Recently，i try to install the tool chain of nrf connect sdk as the instruction as guide。After installed west，then run command “west update”，but got an error：
Can...
Hi ... folks
I am using nRF52832 and analog IR sensor , Working with the example saadc . In this case , i am giving the IR sensor input voltage as 5v , analog pin 2 .I am...
Hi,
I am using NRF52832 Development board, SDK(nRF5_SDK_15.3.0_59ac345) from this i am using (/nRF5_SDK_15.3.0_59ac345 (4)/examples/ble_peripheral/ble_app_uart) example...
Is the nRF52 RSSI block of the RADIO module based on the entire 2.4GHz ISM band, or can it be configured to only measure a given 1-2MHz band of interest? According to the...
I'm using the serial library for the first time. What are the advantages/disadvantages of using IRQ and DMA? How should FIFO queue and buffer sizes be chosen?
Hi,
I am using the following code to implement a millisecond timer read function. In main, while loop, I do nothing but run a 1ms delay and measure the time in mill second...
Hello, I'm a researcher.
I wanna use Bluetooth CTE(Constant Tone Extension) feature with 1-antenna TX + 1-antenna RX.
I have seen some articles that nRF52840 DK does...
I am using nRF52832 with SDK 16.0.0. I have a simple application that uses SAADC and BLE. It reads values from three channels AIN0, AIN2 and AIN4 and sends them via BLE every...
hi all,
we're developping an application to control the frequency and the duty cycle of a pwm signal throuth ble .
firstly we have built both the functionalities separatly...
