Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hey All,
I'm using the nrf52840 for gathering device information from Bluetooth devices having an nrf52 chip on board. The application runs through connect/disconnect...
PROBLEM:
My nRF24L01 transceiver occasionally stops working (about every 2 minutes) when receiving and transmitting data packets.
I found that when the power supply occasionally...
I'm looking at the secure boot in the sdk for nrf52840 and have noticed that nrf_bootloader_flash_protect uses the ACL to protect the MBR and the bootloader from being overwritten...
Hi,
I know it sounds ridiculers, but i just can not flash bootloader into 52840.
I am under S140 v610, SDK v15.2.
I started using open_bootloader in example ( pca10056_usb_debug...
hi,
We are working on nRF9160 DK board.
One of the issues is how to save secure data (e.g, data key) into flash. Is there any examples or document on data storage APIs...
Hello,
i am developing on nRF52840 using SDK 15.2.0 and Softdevice 6.1.1.
I recently noticed, that when i first bond with the nRF52840, then disconnect and delete the...
Hello,
I am using nRF52840 development kit and I wanted to know with use of the source code of nRF blinky application can i modify as per my project requirement and make...
I am connecting debug out on the NRF52 DK to a production board for programming. I am using Tag Connect connection and need to make sure I route pins properly. I cannot find...
Good morning,
I'm developing a new product based on nRF52840 and S140 (v6.1.0). I'm able to connect using my smartphone using the following data:
sec_param.bond = SEC_PARAM_BOND;...
Hi, sorry for if this has been answered elsewhere.
I am currently designing the production setup for a product using the nrf52840 as a BLE radio.
I can't find how the...
Following this tutorial: www.novelbits.io/.../ some doubts arose in my head.
My doubts concern Android app witch name is: nRF Mesh. This application is used only for Provisioning...
Our BLE DFU has stopped working in SDK 3 so I have tried to simplify it by going back to SDKs.
If I compile D:\NordicSemi\nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac\Examples...
Hi, I have a question about Bluetooth mesh secure provisioning, as it is described in the spec section 5.4.3.
The spec states that either
1) both OOB public key exchange...
We are looking to implement "dynamic" BLE services that can be configured (i.e. enabled/disabled) externally, however from the examples there appears to be no way of de-initialising...
