Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
I am using the nRF7002DK development board, which features an nRF5340 as the Host MCU for the nRF7002 chip. I am testing the " Wi-Fi TWT Sample " sample project, which allows...
I have designed a PCB using the nRF52840 microcontroller and the MAX30001g ECG sensor. The sensor requires a 32.768 kHz clock signal via its FCLK pin, as shown in the attached...
I believe I have discovered a bug in the SLM firmware. I am using SDK v2.6.1.
When running the nRF9160 in MQTT datamode, we are encountering an issue where the slm_quit_string...
I have successfully setup my nRF51822 chip with Wireshark to capture BLE packets, using the 4.0.0 release of the nRF Sniffer software (extcap folder). However, the capture...
Hi,
I am currently using nRF Connect SDK v2.5.3 and want to update to a newer version, because I want to create a board definition and I want to do it in HWMv2.
Even though...
Hi! Recently, I tried putting my nrf9160dk into SYSTEM OFF mode. The code instantly puts it into SYSTEM OFF mode and waits for a gpio interrupt. The problem however is that...
nrf5340+nrf7002 running Zephyr with NCS v2.6.x.
When trying to connect to a wifi AP with incorrect credentials, I have several issues:
1/ the result of the (failed) connect...
Hello, After doing several things on my Ubuntu 24 host (I don't what might cause problem): -> Updating java OpenJDK to 17 -> running apt update & upgrade -> modifying my script...
I am encountering warnings while attempting to send Bluetooth notifications in my Zephyr-based project. The warnings are preventing successful notification of ECG data. Below...
HI ALL,
I am using v2.8.0, NRF54L15,and peripheral_uart demo has not made any modifications except for adding the following content. The test shows that the OTA upgrade...
1.test code
the code run separately on ble-softdevice and only timer demo .test code as follow:
2. test data
test result as follows：
picture A,show timer2 timing...
Hi,
I am using nRF Connect SDK v2.8.0 and nRF54L15-DK.
I am about to design custom hardware and have a question.
For Matter, I am trying to use the following pins for...
I am working with the unicast samples where one board is configured as a server and the other as client. Initially i had trouble installing the SDK, but it seems to be working...
Hello.
I am developing using nRF5340DK and nRF Connect SDK v2.8.0. I want to create a DFU distributor that updates both Application core firmware and Network core firmware...
