Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
Hi everyone,
I'm using nrf52840 as a connectable advertiser. Used ble_app_blinky example with some modifications. And I reduced the advertising interval to 2 seconds....
Hi, I'm using the example "libuartes" and developing 2 UARTE. But I dont know how to recoginize what port are communicating with external device because I only have 1 uart_event_handle...
Hi, Im trying to use nrfjprog from inside a docker container (ubuntu). I have started the container with --privileged and it seem to work but when i try to run the container...
Hello.
I use nRF52832 with SoftDevice and several TWI-connected IC's.
The power consumtion of nRF52832 is 14 uA after TWI initialization (low power mode and DC-DC regulator...
Hello, i have six buttons on my custom board, these buttons are inited with following code:
(there are pull up resistors present, hence NRF_GPIO_PIN_NOPULL is used)
SEGGER_RTT_printf...
Hello,
We are using nRF52840 chip for a power-sensitive application.
We use the UART which is connected to a LoRaWAN module.
Now when I enter the system ON mode after...
Hi,
I just started working with Zephyr and having some problems right out of the gate.
Board: Nordic nRF52840DK Example: i2c/spi_fujitsu_fram Branch: Main
When I'm using...
Can Nordic team be sure that SweynTooth test team has tested Nordic chips? If so, the claim in Nordic dev zone that Nordic chips are not listed indicating Nordic chips are...
I have followed Einar's response on the below thread but I still cannot see the logs on the SES
https://devzone.nordicsemi.com/f/nordic-q-a/79682/adding-mcuboot-bootloader...
Hey devs,
I'm trying to get the i2c interface to work with the MP8862. I followed the TWIS driver guide to get started and in there everything worked.
Now I wanted to...
Hi Everyone,
I'm using VS Code, nrfConnect SDK v1.7.0
I'm trying for minimal bluetooth roles(either central/peripheral) along dfu support in nrf52820 chipset.
when I...
Hello,
I recognized a wrong answer is sent by the ZigBee stack of nRF Connect 1.5.1 and 1.7.0 (and others).
Eg. the application provides a color control cluster as a...
Hello.
It is developed using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
I am implementing the advertisement processing, but the advertisement stops when...
Hello,
I compiled pc-ble-driver from github and it when i debug heart_rate_collector in adv_report_parse function i only get 1, 10, 255 field_type and never BLE_GAP_AD_TYPE_COMPLETE_LOCAL_NAME...
