Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
Dear friend，
I am doing a test like this: 1. Connect the Bluetooth device with the nrf conncet app of the Android phone. 2. The notify (CCCD) is enabled. 3. Click "disconnect...
Hi,
we are using D- and D+ in our nRf52833 board, I want to use the CDC ACM USB class as Virtual COM port.
I found that there has a demo example in the \examples\peripheral...
Hi,
We have a problem that occurs when
1) the GPS is at bootup of nrf91: indoor when we start the GPS search, and it doesn't find anything or maybe just 1 satellite...
Hi,
Looked through PS v1.3 didn't see any reference, so probably the answer to my question is no.
But can you please confirm that for me - does nRF52833 support boundary...
Hello,
I am doing tests on nRF9160 DK and I observe that if I send more than 1024 bytes on a TCP or UDP socket, the bandwidth drops.
Here are some numbers :
for...
Hi there
I mount the 19pin connector on nrf5340dk board and connect to segger j-trace pro . The debugger function work well.
Later i modify the nrf9160 etm trace project...
Has anyone had success getting triggers on motion to work with the LIS2DH? I only have INT1 wired so I modified the drivers to work on INT1 as the spec document says it should...
I'm writing software for nRF52832 using nRF5 SDK v17.0.2
I'm using a timer to create a buzz/tone using timer 3. This works as expected.
I'm also using the SAADC to measure...
I'm learning how to use OTA DFU (via BLE) now. I have Python 2 and 3, pip installed in my Win10 laptop. When I install the nrfutil with PowerShell, I had some errors (see...
I've been using the nrf connect toolchain for a bit, and after some initial trouble it was working ok, but now its randomly giving this error whenever I try to build anything...
Hi,
I am trying to convert a number from little endian to big endian. There is a built in function "NTON" that I can use instead of writing my own code, but I can not find...
I'm using two nRF52805 to get sensor values and send 2 sensor real-time values to my phone via BLE. Each nRF52805 BLE works well (Individually tested by nRF Connect App. It...
The encoders I am using generating about 500 pulses per second, and I need to read 3 of them at the same time. I assume a good approach for that is to use the hardware timer...
Hi, working with NCS v1.4.2, I see building products for an <app> landing into subfolder <app>/build/, in several flavours
app_moved_test_update.hex app_signed.hex app_test_update...
