I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
I have application developed that works ok on nRF52 DK (nRF52832) with S112 and now want to migrate it to a custom board with nRF52840.
Could you confirm that S113 is...
Hi:
Since we have a issue that when nRF52840 setting to DCDC mode, our inductive touch will have bigger noise, if setting to LDO mode, the inductive touch noise disappear...
Hi,
I've been trying any way I can think of to work around an issue "51" returned by nrfjprog executed from nrfutil when trying to run serwer from the steps in tutorial...
Hi experts
i am using nRF Sniffer to decrypt the BT Mesh packets with Wireshark, it can work smoothly. However, i tested and found that the packets device key encrypted...
Hello, I am looking at the mesh dfu example code on nRF mesh SDK-4.2.0 on an dk_nrf52840 and I have some questions.
Rather than having both a bootloader and main application...
Hello.
We are developing products using BLE modules.
The one used for that module was "nRF52832 (512kB Flash, 64kB RAM)".
I would like to know
Question 1:
As a...
hi ,
I am working on the nRF52832 , I am trying to store the values in structure and then passing over BLE . I am getting this error after print statement unknown function...
Hi,
I am trying to evaluate nRF5340 FOTA update via Bluetooth. I started with the Bluetooth/peripheral code sample as the basis for my project. I modified the project per...
Could you clarify the use of nrf_esb_set_retransmit_count function?
From what I understood, if it is 0 and it sends a message that wants to be acknowledge , it will not...
To setup the UARTE for use in Zephyr I've configured a nrf52840dk_nrf52840.overlay as Zephyr documentation suggests:
& uart1 {
compatible = "nordic,nrf-uarte"...
Hi, I'm setting up a timer to invoke (via PPI) the ADC in scan mode. It'll read to channels with MAXCNT of 10,000. The ADC built in timer has a value from
[80..2047...
Hi,
I can run the following code within main.c successfully, but it produces the error as shown in the attachment upon execution of k_free(mem.ptr) from with aggregator...
Hello,
in our project we have a nRF52840DK as Central and a custom nRF52832 board as Peripheral. The software on the Central is based on the ble_app_uart_c example and the...
Hi
We are using Nordic NRF52840 in our design. Normally we are using DCDC mode with VDD and VDDH together [Normal mode] connected to 2.2V. In a special case we wanted to...
Hi everyone,
I wanted to make reset pin funtional on nRF52 DK while using pca10040e folder so that I could develop on nRF52810 later, but the reset button did not work as...
