Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
We are going through regulation certification testing. And lab is asking what is power tolerance for BLE 1Mbps for the chip. Where can I find this value?
1.Cant make P0.09(NFC1) and P0.10(NFC2) outputs?
Tried both nRF52832 from PCA10040 and a BT module with nRF52840 and on both cant make any of those pins outputs. Tried with...
Hello
I want to test LE Coded PHY S = 2 (500 Kb / s) using the nRF5430 PDK. The SDK used is nRF Connnect SDK v1.4.0.
There is confirmation there.
1. Does nRF5430, nRF...
Hi there,
I am developing an application that uses UART. I am wondering what's the proper way to connect the nRF52840 to the PC. I researched online and found that I could...
I have a few nRF52833 development kits and want to get started with Keil (MDK-ARM). I could not find example projects in the packs that run on the PCA10100 board. Beside of...
SDK 15.3.0, code is based on examples\ble_central_and_peripheral\experimental\ble_app_att_mtu_throughput.
After getting the project to work with nRF Connect on the desktop...
Hi,
just start with SEGGER Embedded and use a usb acm to setup my target
to have a clean structure I moved code from main.c to dedicated files have the USB and BSP
I...
Hey all, I'm new here. So far things have been going pretty well, I am just having an issue with PPI that I can't quite figure out, but I think I'm close. I currently have...
Hi,
We have been working with a coordinator and an end device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
Both devices are Zigbee 3.0 and implement...
Hi, I'm working on DFU mesh no serial example (dfu_no_serial_nrf52833_xxAA_s113_7_0_1 ) and want to know any way to check it maybe by using nRF Toolbox or nRF Connect mobile...
I have the Adafruit PN532 Shield v1.3 mounted to an nRF52840 DK, trying to run the ble_nfc_pairing_reference_c example from SDK 17. With no modification to the example code...
I'm calling nrf_drv_uart_rx_abort() in order to read partially captured input from UART in my event handler.
However, instead of receiving a NRF_DRV_UART_EVT_RX_DONE event...
Hello,
We are currently developing a project based on nRF52810.
We are testing some examples to learn more about this chip.
Now we would need to know which signals and...
Hi,
I have gone through this ticket --> https://devzone.nordicsemi.com/f/nordic-q-a/30104/how-do-i-share-private-questions-with-my-coworkers-using-the-new-devzone
But...
Hi,
I am using NRF52840.
After upgrading to SDK 17, I found that the chuo stays in boot mode because this new condition (I highlighted it in the code below):
if (NRF_BL_DFU_ENTER_METHOD_GPREGRET...
