Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I am getting small power spikes but cant seem to pinpoint what is causing them.
The smaller spikes in between the transmissions. (The wave is clipped from the top so the...
Hello,
Has there been any success with getting the python bindings for the pc-ble-driver running on openwrt? I've succeeded with the driver itself but not the bindings....
So with the errata in mind the RC oscillator has a accuracy of +/-500 ppm, while the XTAL on the nRF52 DK has a accuracy of +/-20 ppm. During the longest waiting period of...
I have your full eval board as well, I also have multiple NB_IoT sims from Vodafone but have not tried them yet. How do I get your Thingy:91 unit with your sim running please...
Hello,
I want to implement a data logger that will save events in an external flash (even if i think i will start with the FDS). My purpose is to identify some behavior...
Hello,
I am looking to start an independent project this month. One of the tasks will be to use BLE to relay information from a custom PCB board with the nRF52810 chip...
nRF51822
S130
SDK11.0
The power consumption immediately going up high to 1MAH once I enable TWI using this code:
NRF_TWI0->ENABLE = TWI_ENABLE_ENABLE_Enabled << TWI_ENABLE_ENABLE_Pos;...
Hello,
When I added the below lines I get some error:
NRF_BLE_GQ_DEF(m_ble_gatt_queue, /**< BLE GATT Queue instance. */ NRF_SDH_BLE_CENTRAL_LINK_COUNT, NRF_BLE_GQ_QUEUE_SIZE...
Hello,
I have been looking through Nordic's documentation for the nRF9160 and trying to find voltage ranges for several pins but am having no luck. Can someone please answer...
iOS is using queued writes to send data to my nRF52832 application. For some reason, on the third queued write reply (in nrf_ble_qwr.c) sd_ble_gatts_rw_authorize_reply returns...
I'd like to build a prototype using the nrf9160DK that samples audio from a microphone and plays it back. Given that the dev board has Arduino compatible headers, I'm assuming...
Hello,
we are trying to add log functionality to our application (nRF52 SDK 15.3 SD6.1.1) and we have few questions:
1. can two uart and flash backends coexists in...
I'm trying to do step-through debugging with the nRF9160 DK using Segger Embedded Studio and it's jumping all over the place. I assume this is due to optimization but perhaps...
