I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
Hi there,
I have just upgraded the SES to V4.16 and followed the assistant guide in nRF Connect. I have deleted the old ncs folder (and all files) and also created a new...
I measure 184 uA of current during WFE. I've read in other posts that the nRF52832 should draw about 1.2 uA during WFE.
I've looked over the project settings many times...
Greetings,
I am using nRF52840 Dongle and nRF Connect v3.2.0 PC application to scan for nearby Bluetooth devices and connect to them.
I want to develop a PC application...
Hi, I use in my design a component which use the nRF52840 - WLCSP package.
I use SPI to connect the nRF to a SD card slot. With the package, I understand that pin K4 (P0...
Hi all,
I am debugging the data transition flow of the Node with Relay.
We modified the example of ONOFF_server. We found that the unicast address should the odd number...
Hi, I cannot find my Nordic Thingy91 as a USB connected device in the nRFConnect desktop application.
I tried to connect the Thingy via a JTAG 10-pin cable via an external...
Hi,
Greetings!
I am trying test DFU example for nRF52832 and I need help to move ahead.
Setup:
nRF52832 SDK for Mesh V3.1.0
nRFSDK V15.3.0
nRF52832 Development...
Dear all,
I just played around with the nRF Sniffer and I am pretty impressed. Really good tool and most of the packets are received.
I want to build an application where...
I have reprogrammed the nRF52840 board controller. When I run the lte_ble_gateway application I get the following on the 2nd dev kit VCP port:
SPM: NS image at 0xc000...
hello, i have a question, i use sdk15.3 for nRF52832, i run for example flash_fds, sometimes it will not be able to erase or write to memory, after restarting the device,...
I'm having a problem that I get some presumable interference between a high flash memory activity and UART communication. I'm writing single words into flash quite often,...
I am working on a mesh network and i want to add a nordic thingy 52 to read temperature & humidity data over the mesh, let say to an nrf52 DK connected to a Raspberry Pi,...
I'm developing a Zigbee coordinator that works as an On-Off Switch for the Zigbee Profile HA: this connects to the Device Mains Power Outlet, again with the HA profile.
...
Hello to all,
I have a question about parsing zigbee commands when they present a payload.
I have a Coordinator that implements the Window Controller Device of the HA profile...
Hi folks,
Im trying to run the heart rate collector from a Visual Studio application and I have some communication issues with the connectivity device. I use a nRF52 Dongle...
