I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
I am using TWI sensor example to read data from mpu6050. The program runs without error and showing expected values in watch window. In order to see the real time values i...
Hi, I'm using the nRF52840 Preview DK to get data from a digital microphone via a PDM interface. I'm using a clock frequency on 1.032 MHz to activate the microphone. The data...
Hi,
As discussed in this ticket we need a way to reduce the current consumption.
The LPN example doesn't solve this for us.
Our application is based on the light switch...
Hi, we have the latest Xcode installed on our new development Mac (up to date iOS too).
When we downloaded the iOS nRF toolbox from git hub today we get errors when compiling...
Hello Everyone,
I am looking for an Eddystone example. It should be used for an nrf52 with s132 SoftDevice (programming with nrf52 Prev Dev Kit).
Thanks for help
I'm struggling with how to properly identify an unprovisioned mesh device. Basically when i scan for unprovisioned devices from my iOS app, I'd like for only our devices to...
If I use sdk12.3 pca10040 S132
softdevice is s132_nrf52_3.0.0_softdevice.hex
How do I determine what version of Bluetooth it is?
In SDK or where the document has instructions...
Hi, I had download the nRF5_SDK_15.3.0_59ac345,but I couldn't find the softdevice S112 hex.(Nordic52\nRF52_SDK_Source\nRF5_SDK_15.3.0_59ac345\components\softdevice\s112\hex...
Hi ,
We have the following setup :
One nrf52840-dk acting as a multi-link central
One nrf52840-dk acting as a peripheral ( blinky app )
Both communicate well over...
I want to expand the Asset_Tracker example by adding the possibility to send data through UART2 to the controller and then to the nRF Cloud.
I am unable to find any document...
for 52840, customer want to have a part of flash, it can set write protect, to avoid illegal erase or destroy, they use this part of flash to run boot-loader, is it passable...
As far as I could see, only GGA NMEA sentences are enabled by default. I want to check if RMC sentences deliver positions faster, and in my prj.conf I do the following:
...
I got an nRF52 DK and I was unable to recognize the JLINK driver by connecting to my computer via USB. My SEGGER version is 6.44E and my own jlinkV9 is normal. How can I solve...
hi all ,
now , i need add create mqtt ble gateway .
it compiler failed follow message :
C:/temp/ncs/zephyr/drivers/serial/uart_nrfx_uarte.c:1272:9: error: 'DT_NORDIC_NRF_UARTE_UART_2_LABEL...
