Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
www.silabs.com/.../ble-mesh
Do we have similar test program as if silicon Lab?
As I am about to build some PC/Android program to demonstrate the Bluetooth Mesh Device...
I use another jlink ob board to connect to nrf52832, and when i use j-link v6.16c，it give a warning prompt "The connected j-link is defective", and i use jlink v5.12f, when...
Hi,
We have some devices in the field, and I'm occasionally seeing reboots due to NRF_FAULT_ID_SD_ASSERT. I'm logging the id and pc passed into app_error_fault_handler...
SDK13, S132
Project stopped after start. I use standart initialization:
static void peer_manager_init(void)
{
ble_gap_sec_params_t sec_param;
ret_code_t err_code;...
I've connected some sensors using I2C and SPI to a DK and their power consumption is not being reflected in the PPK. Without any BLE acitivity, the current is almost zero...
Hi,
I am using Ubuntu 16.04 (64-bits) OS.
I installed JLink_Linux_V620b_x86_64.deb and was using nRF5x-Command-Line-Tools_9_6_0_Linux-x86_64.tar
I can capture the...
Hi,
I use SES import my keil project, and my keel project work well. With SES, i meed a problem, that is , i have a global variable like this:
uint32_t g_ulMainLoopCounter...
Nordic51822 no external 32.768 k of crystals in the routine what configuration
Use this routine
nordic\nRF5_SDK_12.2.0_f012efa-3d\examples\ble_peripheral\ble_app_bps\pca10028...
When I am stepping through my application code crashing at
memset(&cccd_md, 0, sizeof(cccd_md));
"Setup information:
IDE: Using IAR
Device: nRF52832
Soft...
I'm using the NRF51822 for a project that will be powered by a lithium battery. I'm wondering if it would be safe to use a diode ( such at this one ) to drop the 4.2V LiPo...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello,
For BLE, there is always an ACK in link level no matter it's write/read/notify/indicate.
How about 2.4G proprietary mode? Is it possible to just send a data without...
Hello,
I am using the nrf52832 with SDK v12.3 and PCA10040. Not using any soft devices, nor the RTC. The program is intended such that timer0 is set to toggle a pin (P0_11...
Hi,
We are working on Automotive project using nrf51824. below are some queries ,
We are basically want to use the chip as a Bluetooth to Kline(using Uart) bridge ....
