Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hi everyone! I have a custom board with the Adarfuit UF2 Bootloader ( https://github.com/adafruit/Adafruit_nRF52_Bootloader) and a SoftDevice. With the old SDK v2.5.1 I created...
Hi! So I am trying to control two micro servos, MS18 with the nRF connect app. So far I have the code where I can control it with one instance, and hitting the true false...
I am trying to work with a BLE Mesh network. I am using the nRF5340 as a light and another board, the BGM220, as a switch. Both are provisioned and configured, but the switch...
Hi everyone,
I'm currently trying to build a program with the extension "nRF Connect", and here is how i proceed :
- add build configuration --> nrf5340_audio_dk/nrf5340...
Hey there! I'm looking for the official license info for nRF Command Line Tools and nRF Connect for Desktop. We want to install these on our work computers, but need to check...
Hello,
this is the first time I work with this device and the device is not for me or for my company.
I have to do an automatic test application, which should program...
Hi there,
So I am using an adapted version of the echo sample for I2S in the nRF Connect SDK in VS Code. I only want to use the echo example in receiving mode, so I have...
Hi, I'm using the nrf9160 with ncs2.7 on a custom board. Does the APN need to be explicilty set with `CONFIG_MODEM_ CELLULAR_APN` ? Or will it auto detect? Does it depend...
Hello,
We are using the NPM1300 with a lithium polymer battery that has integrated cell protection.
When the battery reaches the over-discharge level due to prolonged...
I got the following setup: nRF52840 - GenOnOffClient (Light Switch Sample) Publish to Group 0xC001
nRF52840 - GenOnOffClient (Light Switch Sample) Publish to Group 0xC001...
Hello!
I have a complex issue that I am trying to brainstorm. The task is that I am trying to receive a file over the air and be able to serial flash my STM32U575xx.
...
I have customed my own nrf54l15 board and run peripheral_uart demo successfully. Then I tried to measure its current while running peripheral_uart demo, it was up to almost...
Hi,
I've received the nRF54L15 DevKit and tested the power consumption during sleep Testproject in GIT: https://github.com/marcel-cd/nrf54l15dk-powertest
The result was...
Hi,
I am currently migrating from NCS 2.5.0 to 2.7.0 and running into an issue where the CMakeLists of mcuboot ( https://github.com/nrfconnect/sdk-mcuboot/blob/4c7942e58c5458ce3c4e50d3169e0f865910fe87...
Hi I use nRF52832 and nRF Connect SDK v2.6.1 with visual code
I went through this exercise ( academy.nordicsemi.com/.../) and the FOTA works so far. However, in this example...
