Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Greetings,
We switched from nrf9160 to nrf9161 and got the first boards manufactured. NRF9160 has been working fine but we wanted improved GNSS functionality on board. ...
Hi all,
I have plenty of experience with the Old SDK, IAR/Keil/SES, nRF51, nRF52, Soft Device, etc. However, I'm new to the nRF Connect SDK, VS Code and nRF5340. I've successfully...
Please let us know which PINs of nrf5340 are used by BLE stack and which pins are used by peripherals like UART0 and UART1? We are converting our code from nrf connect V 1...
Hello,
We are evaluating MCU's for a low cost Central device that is extremely cost constrained. The nRF52805 and the nRF52810 both have the same RAM (24 KB) and FLASH ...
Hello,
I'm stuck in the nRF Connect SDK Fundamentals course on lesson 3, exercise 1. When opening the COM port to view the printk messages, I get an error when connecting...
Hi,
I am working with nRF5340 and nRF Connect v2.7.0. When I try the mass sample it works fine. When I take the code to my custom project, I have
ff.h no such file or...
Hi,
I am currently working on communicating between the nRF5340 DK and the nRF5340 Audio DK over BLE. Could you please share the information flow?
Warm regards, Rajendra...
Hi,
We have modified the throughput example of NRF5340, v2.6.1 SDK to achieve around 600 Kbps for iOS app. Attached is the sniffer trace.
Can anyone confirm that the data...
I'm seeing duplicate data packets while analyzing our sniffer trace from NRF5340 to iOS app. However, there is no packet loss or any impact on data rate.
What might be the...
Board: nrf5340dk (build board: nrf5340dk_nrf5340_cpuapp) / SDK: v0.16.8 / I'm a complete beginner who touches the nrf board for the first time My Project: max30101 --(measured...
Hello
we have some own created UART drivers which access the UART registers directly.
Those drivers have been working withe the older chip revisions for years.
Currently...
Hi,
I cannot resolve the problem while setting up modem trace RTT logging. I'm also unable to find up-to-date information on how to set this up.
I have connected DK as...
I'm close but this is not working for me yet. I'm trying to send a few hundred bytes from android to my nrf device. So I tried to implement long write where you set prepare...
Hi I've a side request, into the exercise I've to perform some changing into the DK programming interface through the JLink, so the question is how to restore the predefinite...
I am getting an fs_close() -5 error (-EIO) when I write to an SD card using fatfs. I determined this error was associated with FR_DISK_ERR in fat_fs.c.
Additional info ...
