Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I've recently picked up Thingy 53 and NRF7002EB shield and wanted to play around with it, but I have a problem during project configuration.
When I add -DSHIELD...
Hi, I just tried installing nrfutil on linux with aarch64 architecture and with i try to use it i get error.
how i installed it:
after installation I ran the...
Hi, With nRF5340 DK, I am using CC registers of NRF_TIMER2 (as a free-running Timer), and DPPI, interacting with Radio. I set up a Timer Compare (functioning as a timeout...
Hi, I am having trouble setting up the partition manager in external flash with nRF54L15dk in NCS 3.0.0. I did not find any examples of this working. Interesting thing is...
1、How can I find the QEDC configuration for NRF54L15 or the QEDC demo? I found that Nordic courses do not offer these options. 2、Another issue is that I am using QSPI routines...
Hello,
If I set the connection interval to 300ms, can I call bt_nus_send multiple times (e.g., every 100ms) within that interval?
Additionally:
How can I check if...
Hi,
As the subject says, is there any way to get satellite count through at commands while using the AT firmware on NRF9151?
I'm currently using AT firmware version 2...
Hi
Is there a undocumented register to control the CC1/CC2 inputs?
Many power-banks switch off it's output if the current falls below a certain value (e.g. when the devices...
I am wanting to use the castellated pinouts on the nRF7002 expansion board.
I have the nrf7002eb.overlay file open and it has defined two pins that do not make sense to...
我们自己用nRF54L15做了一个硬件，和Android BLE调试助手链接都正常， 和电脑端连接大概有30%的概率能连接成功 我用的是主要报错是Failed to subscribe to characteristic: 6e400003-b5a3-f393-e0a9-e50e24dcca9e. 订阅读取数据特征失败
Hi
When l was using the function ble nus_c_string_send0 for datatransmission, an error occurred. The error code was 0x00000008.And at this point, the system resets.l don...
name:
Code:
Log1：
When the storage capacity is 64 entries, continuously reading 32 of them takes about 2 seconds.
After changing the path, run the write and...
