Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
We are using over own server that host multiple apis for different functionalities.
I am able to make http post requests to all of them individually and everything works...
Hi
I am about to make an application where a device is sending a sync pulse (60Hz) out to a number of Host's.
when I test with a device and a host, I get approx. 1.22ms...
I am having trouble finding a commercially available BLE 5 dongle that I can be confident will support Linux BlueZ as well as the LE 2M PHY. I would like to know if I can...
Hello,
I have an evaluation board with a nRF52832 chip on it. I added some code to ble_app_uart example and flashed it on the evaluation board.
Here is my problem: I added...
Hi,
I'm trying to use BLE to send data to a computer from the NRF52840 DK. So far I'm trying to get nrf_sdh_enable_request() to compile without errors, but I keep getting...
Hello,
I have both an installation of NCS v1.5.0 from Toolchain Manager (TM) and from the Getting Started Assistant (GSA) on Macbook running macOS High Sierra. The TM SDK...
Hi
I am using nRF9160DK board and need transmit gps data to web site, I am trying with udp but have problems with that, I would like to know what protocol use asset_tracker...
Hello,
at the moment I am trying to implement a counter that increments every 1ms. I wrote the following code for this:
Regarding to the documentation ( https://infocenter...
Hi there,
I am running a custom board based on the nRF5340-DK. It's a minimal board, notably with both oscillators
It seems to behave itself with low-rate BLE use-cases...
Hi.
I'm having trouble flashing my Thingy:91 with the nRF9160DK as a debug probe.
The DK is set to 1.8V, I have a 10pin JTAG cable connected to the debug out of the DK...
What is the UICR setting in nrf51822,S110? Currently, when I develop with nrf51822,S110, the UICR area is 0xFF. I want to set the UICR as follows, is there any way to set...
Hi,
I am using multiple channels of SAADC for monitoring some data and then I send every 20 samples of adc in a 32 packet through Radio/BLE using the esb_ptx example and...
Hi All,
I am a beginner to nRF52 and Nordic Microcontroller, I want to understand the flow of code and its BLE sequences in detail . I am also not proficient in the C language...
