Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
Hello,
i have been struggling with this issue for several days now, maybe due to my limited knowledge of thread networks.
I'm developing a solution where some devices...
Short version:
- Can you enable debug output in the mbedtls used for DTLS in OpenThread, available through the nRF SDK? If so, how?
- Can you at all chan ge the list of...
To the kind attention of Nordic support team,
we are using secured gazell library in our devices. We would like to pre-pair couple of devices (host-device) using valid secured...
Hi i am working on project where i need to store logs on flash, i included nrf_storage and set start address 0x42000 and end address 0x50000 according to my application, my...
Hello. I want to use nRF52810 as a connectvity platform connected to OpenWRT MIPS based board via UART. For some reason the only solution I can assure is to use 2 wire UART...
Dear Nordic support,
We are using SDK5 15.2.
Our application uses FDS to maintain configuration. One issue is that we have to change the configuration via phone app regularly...
Hi,
I am working on nRF52840 DK . C:\Nordic\SDK\nRF5SDK17009d13099\nRF5_SDK_17.0.0_9d13099\examples\peripheral\ uart I am sending data from Arduino and showing it on PuTTY...
Hi All:
I try to create a custom Characteristic,with nrf_ble_qwr,
but when set is_defered_write = 1;
connect with NRF_CONNECT APP, I can't write under than 20 byte,if...
Hi, we just saw that %BSKGEN was added in MFW 1.2.1. However, it is not clear to us what is the intended use of it. Could you please give us a bigger picture of it?
Is...
Hi there,
I have a rudimentary understanding of programming with the nRF chipsets and Segger.
In our project, we are trying to locate the position of a transmitter (nRF52833...
when design the product, BLE output power set at +4dBm, and test the real output power with Spectrum Analyzer. when test at the MCU direct output pin the output power is about...
Hello -
We are developing on the nRF52840-DK, using SDK 15.3.0 and FreeRTOS with tickless idle. The SoftDevice is disabled. Using the PPK v2.3.1 when our app is in System...
Hi,
I have nRF9160-DK kit and its environment is set such as nRF Connect SDK and Segger Embedded Studio.
I want to build a simple application from scratch for example...
Hi,
I have a question regarding our approach to achieving high throughput UART transmission over BLE.
The protoboards we are currently testing have BL654 modules from...
