Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
Hi, all
I'd like to get the whole thread network topology (like nRF_TTM does) on raspberrypi, can this function be realized with wpantund or wpanctl?
Is "wpanctl mfg....
Hello,
I am attempting to integrate FOTA (HTTP Application Update) into a Thingy91 project on top of the LTE BLE Gateway example project.
I am on nRF Connect SDK v1.1...
Hi,
How many SPI slaves can I connect to nRF52832 as an SPI master?
I would like to know the maximum number of SPI slaves which can be connected to nRF52832 as an SPI...
Hello all,
According to the documentation and this feedback on a case there is a maximum size for a particular cert before nrf_inbuilt_key_write returns NRF_ENOBUFS . Can...
Hi,
I am using NRF52832 for development without bluetooth SDK, NFC and RTC.
I am using a development board with SPI and a slave device that can communicate normally (using...
Hello,
Most of the outputs and LTE Monitor use by defaut an UART on DK. Problem on custom boards, for cost limitation, UART is not always present. Probe connector is so...
irq init as below:
I use port event, and muti-gpio irqs. Irq gpio connect a sensor`s irq pin.
I detect irq gpio level in irq_Handler(), high level is my need, the...
Hello All.
I Need help ... first time use "nRF52840"
Goal of this project is "record voice with digital mems mic and play that voice using speaker with i2s"
First...
Searching through the forum I found this guide.
"Getting started with Nordic's Secure DFU bootloader, a step by step guide"
https://devzone.nordicsemi.com/nordic/nordic...
SDK 16.0.0
nRF52DK
ble_app_hts example
The ble_srv_is_indication_enabled always return false no matter in the ble_hts_is_indication_enabled function or in the on_cccd_write...
Hi, im usinh SDK V 15.3
i was following the tutorial to add buttonless dfu to my application code
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Hello,
I am a newbie and need some help deciding the path to perform the following requirement. Any help is appreciated.
Requirement:
I have Rigado BMD-350 module currently...
Hi,
I have a nRF52840 DK (PCA10056 v0.9.0). I tried the long range (Coded PHY) but it throws an error and didn't work. I read in nordic forums that the chip revision should...
We are entering a pre-production phase where the contract manufacturer must program dozens of nRF9160 modules, and we would like to offer a command-line method, to simply...
