Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hi All,
I am using light_control example from Mesh SDK and I need to get something that identify my device in mesh e.g id, address. I would like to send some message to the...
Hi,
This is somewhat tricky question.
In my custom board application program using nRF52832 chip,
I used uart initialization function (e.g. uart_init()) and printf...
Is it possible to use a Nordic nRF52840 DK and a personal BLE board to run the throughput example? What types of modifications would have to be made to both boards?
Hi,
after setting up the LPN-example like described here I can establish a frindship relation.
When I measure the current I can not get lower than 40uA.
I use a Multimeter...
Hallo
I am developing on a NRF51822, sdk12, s130,
I have encountered a repeated unexpected reset to my device (the reset reason vector register is all 0)
which seems...
Hi
I have been developing ok with Segger Tools and nRF52DK. My application works as expected. However now I need to send hex files to a customer who also has the nRF52 DK...
I have a bunch of custom characteristics in a custom service. I have two different modes of operation that I need to handle and the data associated with these custom characteristics...
Combinig a simplified version of the bsp example and the pin_change_int example I noticed that I'm running into an "[NRF_ERROR_INVALID_STATE]" error caused by nrf_drv_gpiote_init...
I'm trying to send a DFU file but i get en error:
2019-08-16T16:11:40.300Z DEBUG Destroying DFU transport. 2019-08-16T16:11:40.300Z ERROR DFU failed with error: When writing...
DIODE_FWD_VOLT_DROP_MILLIVOLTS is normally depending on how the reverse current protection is implemented in hardware. the current value of 270mV is adapted to the used diode...
The coap_client sample is not building for the nrf9160_pca10090 board. I'm using v1.0.0 of the nRF Connect SDK. The commands used from the coap_client directory are:
mkdir...
Dear Nordic experts,
I am trying to profile embedded S/W on a custom board (call it board #1) with a nRF52840 on it. On this board the trace pins TRACECLK and TRACEDATA...
Hi,
I'm currently trying to evaluate the nRF9160 for one of our projects.
One key requirement is the power consumption when using eDRX.
I have tried profiling the...
I noticed that passkey entry for BLE pairing is usually implemented by the device operating system outside the nrf_connect app. Is it possible to do passkey entry inside a...
Hello everyone,
im using ble tamplate example and Softdevice s140 with the nRF52840 DK.
im trying to change the GAP Data. How and where can i do this?
i want to configure...
