Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
Hi,
our device has current limitations in the range of 1mA. We were examining several ways to limit the actual connection parameters to keep current consumption low. But...
Hi,
I'm developing an application to monitor the current application and network context, by extending upon the existing Light Switch example in nRF5 for Mesh SDK v3.2.0...
Hi everyone !
I have 3 services and 13 characteristics in my project. Until today, 3 characteristics were working fine. But i added rest of the characteristics and my project...
Hi all,
I am currently using Pyaci serial to establish and test BLE mesh network, and it work fine.
The further step we want to do is to create a duplicated Provisioner...
I have a Thingy52, but no DK. I would like to know if it is today possible to upload a custom firmware only using OTA (no DK), eventually starting from the Nordic Thingy app...
Hi,
I'm trying to transfer data between an nRF52840-DK and an Android phone which has nRF Connect installed on it and I can only reach about 40kbps (that is kilo bytes per...
Hi, I am working on installing the pc-ble-driver-py library and building it to run an application for a nrf52840 Dongle over serial port.
I have followed github.com/......
Hi everyone!
I have a nRF52840 dongle and I am trying to run python examples from pc-ble-driver-py. The dongle is connected to a PC running Ubuntu 18.04. The dongle is flashed...
Hi,
I am using the SDK 11 on nrf51822 I just merged the TWI sensor example and the BLE UART example. Both work together but the softdevice seems to be slowing down the twi...
Did anyone configure correctly VS Code with nRF Mesh example?
I did install CMake on my computer and download CMake extension to VSCode. I am working on Windows.
I did...
Environment - Mac - nrf tag; 1.1.0 - modem fw: 1.1.0 - DK 0.8.5 - debugging by SEGGER RTT The program polls SMS for a certain time and if SMS is received, it reads the messages...
Hi.
I am trying to update soft_device version 6.0.0 to 7.0.1.
I read that because of the major version change (from 6 to 7), i must update the bootloader as well.
I...
Hi,
I am prototyping with the the THINGY52 using nRF Connect.
I am using the services available to drive the MOSFETs on the expansion connector P4 through the services...
Hi,
I would like to debug the code which is in Nordic Thingy91 by using nRF52840DK.
Is it possible to use the debugger in nRF52840DK for Nordic Thingy91 ?
If it is possible...
Hi,
I like to understand what SBs should I cut, what switched should I use to measure the SOC current only with PCA10056 board. I use the Otii Arc device to supply power...
