Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hi ,I'm using nRF52832 Bluetooth DK and (SDK15.3.0) , I am trying to switch between beacon mode and uart mode without the need to reset button , e.g with reset button from...
Hi,
using a stock nRF52840 dongle and willing to enter bootloader (same as pushing the relevant button on the dongle) from app. How can that be done, using stock bootloader...
Hello,
I am using custom board with nRF52810 (QCAA, QFN32), SDK14.2, and softdevice S112 v5.1.0/S132 v 51.10 according to the compatability matrix. I am programing the board...
I have a question about LE Secure Connections (LESC).
As an example, consider the following behavior. 1. "Device A" scans as "Central". 2. "Device B" advertises as "Peripheral...
I have a question about "Importing Keil projects".
I want to run "ble_app_multirole_lesc (SDK V14.2.0)" using "SEGGER Embedded Studio". However, there is no project file...
Hello,
Currently, I have a product with the nrf52832 SOC and my customer wants to know its life-cyle.. (approximately)
just to take into account possible replacements...
I have a question about LE Secure Connections(LESC).
Is it possible to pair with multiple devices in multi role operation? I am considering the following connection. ・Peripheral...
I'm using ble_app_uart_c example with NRF52840.
And i want to read the beacon device id( 8 byte ) at Central(nrf52840).
The ADDR value could be verified through the questions...
Hi, i'm using nrf52832 uploaded ble_app_beacon example.
I want nrf52832 to work as a beacon and as a nfc tag.
Thus, I added some nfc example code. nfc_t2t_lib.h also...
I'm investigating a failure in 2 devices. The devices are immediately failing in application start-up due to fds_init failure. I tracked the failure back to fds pages_init...
Hi,
I could not find the logic for spi_xfer_done flag (main.c) that is being updated after SPI transfer is done in the SPI example from SDK 15.3.0.
There is no particular...
In light switch example, I am trying to implement relay feature. I used nRF5_SDK_15.2.0_9412b96, nrf5_SDK_for_Mesh_v3.0.0_src.
When compiled light_switch_client_nrf52840...
Hi,
I am using modem version 0.7.0-29 alpha modem firmware. ( I have also checked with 0.6.8-131 version )
I have already done MQTT connection with Azure IOT hub and...
I need to increas the speed using the UART ove BLE application.
I try to add new characheristics to the Nordic UART Service.
I have added the UUID for this new charactheristic...
Hello,
I would like to get AT Command Sample to work on nRF9160. I erased the module using Programmer software "erased all" and then loaded Secure Boot sample, then updated...
