Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Dear experts, please tell me, how can I switch the frequency source for the RTS from STAL to internal RC generator when the processor is running? command sequence does not...
Hello,
im using nrf52832 NRF5 SDK 12.2 , S130 . using the pasted code and i get 1023 on the ADC even voltage is 1.7 volt i using keil ver 5 s130 i double checked the voltage...
Hello,
I have prepared an nRF52840 with DFU example (dfu_nrf52840_xxAA_s140_6_0_0).
When making the DFU package for the blinky example (bin/blinky/blinky_nrf52840_xxAA_s140_6...
Hi all,
I'm working with 2.1.0 version of Thingy:52 firmware (the last version currently). Further I am working on Linux with SEGGER J-Link Commander V6.34c in order to...
Hi,
I want to read register 0x00 (chip ID) of ads1292. i do following...
===========================================================================================...
Hi
I am developing 4 layer PCB for the nRF51822 with a power and a ground plane in the inner layers. I will be using a balun from Johanson Technology (2450BM14E0003) with...
Looking to apply an nRF52 chip in a wearable device... ideally without mounting it on a board.
Is that remotely feasible?
It would still be necessary to connect to 12...
Hi to all,
i have a project that was based on SDK 13 and in that version i had a bility to call fds_record_write with multiple data chunk, but in softdevice 14 and sdk15...
I have integrated the code of the multilink into the uart central example. The project can be built without error. however, it is not possible to establish a connection to...
Hi,
I'm starting development of a new product utilizing nRF52840 mcu. We used this chip in previous product with Bluetooh stack (SoftDevice). I didn't participate on this...
Hello!
Since the code of nRF connect code is open (on github) - is in possible to extend supported devices list? In other words, is there any way to use non-nordic boards...
I would like to know if you can create a mesh network with nrf52840 preview DK?
Would you have a problem with this board?
currently, would a better option create a...
Hi,
Using the reference schematic No.4 given in the NRF52840 datasheet I made a design. I was able to test all the peripherals and range testing without any issues. But...
I am working on a custom I2C bootloader for nrf52832 using SDK 14.2.0. Currently, the bootloader can flash the application code very well. But I have no idea how to flash...
