to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
-Dear Nordic Devteam
Thanks for your endeavor for the nRF Sniffer 2 . Although it is a beta version, this is sincerely anticipating.
To set up the Sniffer you will...
I am developing some firmware using SDK 8.1 where power consumption is absolutely critical. The firmware will make a ble connection between the central and peripheral device...
I'm facing a strange problem that I don't really understand:
I'm using 51822 (s130) on a custom board to communicate with iPhone 5S. The parameter that is able to establish...
In multi-link central app, after BLE_GAP_EVT_CONNECTED event, BLE_LBS_C_EVT_DISCOVERY_COMPLETE is called NRF_SDH_BLE_CENTRAL_LINK_COUNT number of times.
So For example...
Hi,
I use the original "nRF5_SDK_14.2\examples\ble_peripheral\ble_app_uart" no any modification, in Keil the .hex file size is 71k while it is 153k in SES.
My questions...
I am working on SDK V10.0.0 because I need S310 softdevice.
I like SEGGER_RTT I used in SDK V11 and V12.
But I got the Error in the subject line.
I had to uncheck use_microlib...
Hi,
I build below sample in SES and receive an error for:
Compiling ‘nrf_log_backend_serial.c’
can't open '...nRF5_SDK_14.2.0_17b948a/examples/ble_central_and_peripheral...
Hi!
There are many questions about flash memory already.
But I could not find the question I wanted.
I want to save scan data to flash memory.
However, when you...
As a peripheral,S130 can work ok,but when I add a central role, there is a error at central start to connect a peripheral. err_code = sd_ble_gap_connect(&addr,&m_scan_param...
When a peripheral advertises on one of the three advertising channels, does it listen for a short duration on that channel (as implemented by the Softdevice?) And then repeat...
Hello.
I am measuring the current of nRF52832 using Power Profiler Kit(PPK).
I used the following case with PPK setting.
infocenter.nordicsemi.com/index.jsp
At...
Hello Folks,
I am using PCA 10056 Eval board. I am using SPIM0 to connect 5 slave sensors. The Chip select is done by the UART Tx pin. So If I send 0x01 over UARt then...
Review_4Jan.zip
Hello All,
Please review the attached revised schematic and give your valuable feedback.
Please find below queries:
In case you want to know the...
Hii everybody,
I want to do ble pairing(nrf 52832 development board) with android phone. after searching on nordic devzone how to pair device i found that pairing mechanism...