Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi,
I was considering the following scenario and didn't find an answer. Could you please help?
Assumption:
There in a BLE peripheral (e.g. nRF52) and central ...
Im using sdk 14.0 and s132 When i add flashwrite codes to my project which has bluetooth communication ,it does not work I wanna send data to flash and i wanna read/write...
I do not want to use SoftDevice, I want to write new application from application to Code Area(0x00 - 0x80000).
Can I use fds without using SoftDevice?
Also, Is there...
Hello,
I am using SDK 12.2.0 with s130_nrf51_2.0.1 softdevice and running ble_app_hrs example.
My FLASH and RAM settings are:
FLASH (rx) : ORIGIN = 0x1b000, LENGTH...
Hello,
I am using sdk12.2.2 and pca10040. I want that my beacon advertises continuously for 10 sec and then it stops advertising for 5 secs. Do I need to use rtc for this...
As i am migrating to 52 and tuning the ble app, i realized by reading many posts here that:
external HF xtal is not recommended
external LF xtal can be replaced by...
Hi Nordic,
I am trying to implement DFU-OTA in beacon. For that I am trying to make beacon connectable. My requirement is to work the beacon in non-connectable mode during...
Im try to read the RPD register, but always get the same value RPD=0
uint8_t channel=0;
int index;
hal_nrf_set_operation_mode(HAL_NRF_PRX);
hal_nrf_set_power_mode(HAL_NRF_PWR_UP...
Hi ,
I need the BLE peripheral to have 'name1' at the start up and change it to 'name2' when a button is pressed. I want to do this without disabling and enabling the softdevice...
Hello,
I'm in the process of updating our codebase to SDK 14 and am facing some problems getting the CLI to work. My goal is to get CLI and logging to output on the same...
[nRF52840 + SDK13]
On the hardware that I have, the UART driver is hitting a communication error because the RX line is low. This only happens when the UART lines are disconnected...
Hello,
I try to achieve maximum data throughput using pc-ble-driver 1.0 and nRF51(with ble_connectivity) as BLE dongle.
First problem I encountered was the bug with...
Hi,
we are currently testing the nRF52 DK as a reciever for several BLE devices.
For a fist test we implemented some datarate measuring in the:
PC -> nrf Connect -...
Hello,
I am using ndk52 (nrf52832) as peripheral and central in my system. I did some changes on ble-app-uart example for both. Now i can send my packets continiously....
Hello,
I am using ndk52 (nrf52832) as peripheral and central in my system. I did some changes on ble-app-uart example for both. Now i can send my packets continiously....
