I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
We are working on a project where 802154 radio runs on the NetCore. The NetCore firmware is based on the multiprotocol_rpmsg example by Nordic. Additionally, we have a custom...
SDK : NCS v2.8.0
SoC : nRF52840
HW : custom board
Hello,
I was trying to use settings subsystem, and I managed to make setting_write() and settings_read() work....
Hello, our entire code base is built around the Nordic SDK. We are considering designing a system that uses an nRF52840 as its controller but has no wireless functionality...
Setup: The nRF52840 DK is running the peripheral_hids_keyboard sample project. The device is connected to a macOS host, showing expected functionality.
Problem: When the...
Hi, We are using an nRF5340 and nRF Connect SDK v2.6.2. We have set CONFIG_BT_BUF_ACL_RX_SIZE to more than 251 and BT_CTLR_DATA_LENGTH_MAX to 251 in our prj.conf.
W hen...
my program works on the nrf52840 DK but does not work on the custom board using nrf52840-QFAA. We are using nrf sdk V2.8.0 running zephyr. Program is attached.
What to do...
Hello,
Version - nrf Connect SDK v2.7.0
The background to the system I am developing is described here and here
In short, I have an application containing a BLE Peripheral...
Hello everyone, I hope you have a good days. I'm developing an project for military standards. I'm using Nexys 4 DDR FPGA ev. board and VHDL language. My question is how can...
NCS 2.6.0, nrf52840
On our board we have attached a QSPI nor-flash as well as a SPI-based OLED display on the same pins.
I'm wondering if there has been any attempt...
In my application, I have implemented Serial Recovery. The interface used for the transfer is UART0 , which I also use in my application at a baud rate of 1M. When I enter...
I'm struggling to get a peripheral device to work with two simultaneous connections. I have attached my configuration (for the application) and my connect/disconnect callbacks...
Good morning team,
As the nRF7002 has been certified Wi-Fi 6 and registered by the Wi-Fi Alliance, can devices embedding the nRF7002 use the Wi-Fi logo and the Wi-Fi designation...
Good morning Nordic support,
I'm a beginner with the nRF Connect SDK and the nRF5340 microcontroller.
I'm using SDK v2.9.0 (the latest available for my Mac).
I started...
Hi, I have been trying to understand how to modify existing projects/samples by adding aspect that are already supported in the libraries. I have an nrf9151 development kit...
Hi,
I'm working with a company that is writing an app on both android phones/tablets and chromebooks. I'm making a new bluetooth device for them, but also helping with...