I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
Hi,
I am using the nrf52840dk trying to connect my bike power meter over ANT+, to then forward data to cloud (will be using the nrf9160dk and then the thingy91 once I get...
Dear Support,
I'm evaluating a tiny BLE chip that we can do:
reading multiple three SPI sensors: pressure sensor, accelerometer, and FRAM.
So with your BLE chip...
Hi,
Using 52833 it seems that sometimes the radio quits responding, ie, it is in NRF_RADIO_STATE_DISABLED state and there is
no obvious way to get it out of that state...
Hello,
I'm trying to program the ble_app_uart example program from SDK 17.0.2 in Segger Embedded Studio using softdevice 132 to a custom PCB (with the nRF52832 chip) using...
Hi,
I am using nrf9160 to handle the MQTT protocol and collect the data packets from another microcontroller using the UART interface.
Sending the data to the server using...
Hello all,
since Tuesday I'm trying to get the example project ble_app_uart_c (SDK Version 12) running. Meanwhile I can compile the project without errors, but when I flash...
I am trying to set up the nRF52840DK to interrupt on the comparator input on A0 going above the threshold. I figured, I think, how to set the comparator up but I am havin...
Hello Nordic Wizards,
We are in the final throws of a project preparing to go to market. However we have identified a "strange" problem.
if the batteries driving the board...
I keep getting this warning message while I'm running the peripheral_uart sample on a nRF52820. Anybody had experience with this? I assume it has something to do with my heap...
Hello,
I would like to synchronize my mesh server's current time with my smartphone. It is possible using nRF Mesh Mobile Application ?
I saw on the mesh models list that...
Hi, I want to use TrustedFirmware-M as a secure backend for an application that uses Mbed TLS in the non-secure domain, and this seems to be artificially limited - the MBEDTLS_USE_PSA_CRYPTO...
hiii,
I'm using the light switch example from the mesh SDK, version 5.0. I've successfully configured the client and the server using the nrf mesh app. however, my client...
When I do a 'build and run' in Segger Embedded Studio I get this error
Then I press the reset button and everything works.
If I do 'build and run' again the error repeats...
Hi
I would like to add to the scan_adv example, the possibility of the FOTA upgrade.
I can merge the scan_adv and smp_svr examples, and get them to work at the same time...
Excuse me:
1、The customer wants to use p0.21 pin as General purpose I/O，Can the reset circuit of p0.21 pin be removed？
2、The customer said that when a new nrf52832 chip...
