At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
I've been having a ton of issues getting any of the application code to run on my Thingy91. Just tried updating the Modem FW to 1.2.2, however I'm not able to place my Thingy91...
Hi:
52840 with softdevice, I use External low frequency oscillator (32.768K) ,the system run normal,but some days later,system can't run. So,I find the problem，the problem...
The Bluetooth Core Spec version 5.2 says that the " maximum number of CISes in a CIG shall be 31."
Can the nRF52840 support 31 concurrent CISes in one CIG? If not what is...
I want to load the GPS routine project of 9160, but it fails. The error prompt is as follows:
one step
When I click OK, the following prompt appears
two...
Hi,
I have nRF52833 and nRF9160 on my custom board. Due to limited space available, trying to use a common SWD interface between the two SoCs. As follows: 1) SWDIO and SWDCK...
I add the MAC of acquisition device in the broadcast initialization of nrf52810 serial port routine, it can display complete. But I added the Mac to the template broadcast...
Hi ,
My firmware is almost done, and now is the time to optimise power cunsomption.
First, my software has a special mode. Each day it wakes up, communicate with a sensor...
Hello,
We are developing products with nRF52810 MCU. There are only 100 bytes ROM left now. We hope to update bootloader via Buttonless DFU in single bank way. Is it available...
I want to use the four peripherals UART0, UART2, UART3, and I2C_1 on nrf9160. When I was building the project, I encountered the following error.
Here my prj.conf
...
Hi,
I received a Thingy91 and am unable to commission it to nrFCloud.
The Thingy91 skipped orange breathing as mentioned in the manual here (step 4). It went directly...
Hi! I'm running a project with an nrf52 chip for which we use the JLink as the interface. I've been using my setup a lot for the past year. The other week, every LJink command...
Hello,
i'm trying to understand how the management of the SS pin is (or has to be) performed when using nrf9160 as SPI master.
In this post Håkon said that:
"Most driver...
Hi,
I using the radio test example on the pca10040 with nrf52832 EVB.
And set the radio test to Tx, the parameter as below:
Data rate: NRF_RADIO_MODE_BLE_1MBIT TX power...
I have searched the devzone and couldn't find any solution
followed the instructions from Nrf Connecta dn verified as well.. using
tag v1.1.0 (have done west update...
