Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hi,
I am working on a product development that uses an nRF52832 (through a LAIRD BL-652 module).
We have a voltage point (named 5V), that is connected to SIO_28 GPIO through...
Dear,
I used ncs_v1.0.0_joakim to adapt the battery of my thingy91:
I used: battery_monitor_read(); to read the %battery, and it worked well
I just updated new...
I understand correctly that in order to use my private key for my applications, I must first sign an immutable bootloader with this key and upload it to the device?
I used...
Hello there,
It seems the CC310 backend for ChaChaPoly does not allow zero-length data or adata (associated data). I am implementing a protocol that requires this (Wireguard...
I am trying to change the default ATT_MTU size from 23 to 64.
my code uses Ble_nus service and Eddystone_Service.
Eddystone service is in connectable mode and it's where...
Env.: nRF52 customBoard, SES, nRF5_SDK_16.0.0_98a08e2
Hi,
I'am working with ble_app_template example and currently trying, to merge it with the experimental multiperipheral...
I have added an external SPI flash on the nRF9160 DK board, and wired it up to SPI3. I want to partition the flash into two ares for separate uses, but the partition_manager...
Hello.
I have just recived my nrf5340 PDK. I started with the hear rate example programming with the console. With some troubles but finally it worked.
Now I'm trying...
Hey nordic ,
I am doing project on BLE. I am Using Segger embedded studio v4.30b. (Board pca10040).
In that I am using features like advertising ,scanning and connect...
nrf52840 SoftDevice V6.1.0 release-notes written, The scanner and initiator roles can now be configured to receive ADV_EXT_IND PDUs on both 1M and Coded PHY, using a single...
Hi,
I'm using nrf52840 DK to connect and receive usbhid message with the message size > 64 bytes (examples 343 bytes), so the message is divided to multi packages. I modified...
I am trying to build the nrf9160 from segger studio. I have installed and expoerted path of zypher and gnuarm toolchain gcc-arm-none-eabi-8-2019-q3-update-linux
I am getting...
I'm trying to run SDK examples on BL652 module from Laird (which is basically nRF52832) by means of debugger from nRF52 Dev Kit
Strange thing is that all examples (even...
However, I don’t know which SDK we currently use:
“ The new device version is software compatible with the current version if using SDK14.2/15.0/15.2 and Softdevices...
Dear Nordic Community We are about to develop a module for the nRF5340. Unfortunately we are using EAGLE CAD and not Altium Desinger. Would you mind adding the nRF5340 reference...
