Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
I have some question below: note: the project_uuid belong uuid-16bit by my define uuid of product myself.
1. My project uses project_uuid and DFU_btn_less services...
Hi i'm first in BLE
I use nRF52840 DK and SDK15.3.0 and SEGGER embeded
when I excute single example(ble_app_blinky, ble_uart, timer), it has no problem.
but when I merging...
My UART is going into a NO_MEMORY error after trying to transmit a single byte. When i try and put the second letter on the transmit buffer, it gives err_code = 4. I tried...
Hi Everybody
When I run my code with the debugger, it always crashes when executing sd_softdevice_enable(). Even if there is no breakpoint activated. However, when I run...
SDK 15.3 API S132
How can i implement the HFCLK using softdevice or how can i enabled it
I need to be able to run an SK6812 which has the following timing requirements...
I'm attempting to make a custom program using a few different libraries based on the samples. In attempting to initialize nvs, it returns -22. I've been able to trace it deep...
Why does " app:" appear in my serial port when reading from ble_app_hrs_c from the SDK for nrf52dk. I was looking to remove this part sending to the com port but I cannot...
Hello to all,
We have developed our application & the following platform we are using:
SDK 15.0, Segger IDE on windows PC
Softdevice version is 6.0.0
Hardware version...
Hello,
I'm using SDK15.3.0, softdevice S132 v6.1.1 and we would like to know if it is possible to combine the application and the bootloader in the same ZIP file in order...
Are the MIPI and MAGPIO interfaces mutually exclusive, or is it possible to setup nRF9160 to use both? For instance, can I use MIPI to control RF switches, but at the same...
Hi,
I've created a project combining gps, nvs, and mqtt based off the nrf and zephyr project samples. I've been able to go into the sample projects and add .overlay files...
Hi.
I'm dfu test for sdk13.
NRF52832 EVM board
nrfutil version : nrfutil version 3.2.0
D:\nordic_nrf52832>**nrfutil.exe dfu ble -ic NRF52 -f -pkg dfu_test_app_hrm_s132...
Hi, i want to use dfu for application with mesh. But i want to update via ble in direct connection with phone, not via mesh protocol. Should i use example from mesh sdk or...
nrf52832 is connected to the main controller of the circuit on uart lines (RX and TX).
We have observed that even when we completely cut-off the power of nrf52832 then also...
