I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
Hi,
I got some issues with migrating from SDK 14.0.0 to SDK 15.3.0 on a project that was developped from the previous developper. I have already done a lot of migration...
Hi i am a college student working on Iot devices and i m working with hdc2080 and nrf52810 but there is not any ble peripheral source code for twi or i2c in the folder provided...
Hi, I have added the SAADC example into my BLE_UART example and SDK 15.03. i need to use ADC for sampling some adc data.
I added SAADC example code to my application and...
Hello Nordic team,
I'm currently working on a project on a nrf52840 DK with the SDK 15.3.0.
As central role, I have an external component that sends big chunks of data...
Hello,
I'm implementing some ble service that send node id, timestamps, accel values, gyro values.
So I'm trying to modify ble tms service at Nordic-Thingy53-FW .
I...
I have created a custome board for the nrf52810 after having tested its functionality on the development kit.
I have followed the reference schematics contained within...
Hi
Can you please point me to some documentation which shows how to run SD140 with freertos on an 840 chip?
Look forward to hearing from you
Kind regards
Mahendra
When I try to connect my device(iOS Application) to my peripheral(BLE Device), I want to send this passkey programmatically during the connection. I'm using BleManager but...
Hi,
a dumb question. For a board with voltage regulator installed is it allowed to connect SWD VTref to the regulator input (at <VTref1> point)? It's assumed that VTref...
Hello all
I've read various other threads concerning this topic, but I still can't wrap my head around it.
What I think I understand of this topic:
ATT_MTU can be...
Hello,
I'm trying to configure two TWI slave devices on the same TWI bus on my custom board(nRF52832). One slave is RTC, and the other is a biosensor. The TWI configuration...
Currently, I am using SES for development. So when I use the "Build and Run" option in SES the program runs properly. This also generates the .hex file in the Release folder...
I need to set HEX value (uint8_t value[7] = {0x56,0x45,0x52,0x53,0x49,0x4F,0x4E};) on my custom character to be read by my phone. but the value that is displayed on my character...
Hi,
1. I have been trying to measure the current consumption of the development board of nRF9160 in PSM mode, however, until now I could have not understood the role of...
