Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
I am developing software supporting LEsecure using SDK 12.3 with nRF 51822.
Please tell me what to do when incorrect data is entered in "Passkey entry".
Currently...
Hi.
I've been trying to send a payload with STM32F but I can not. I've used both STM32F103 and STM32F3 to send a payload but neither of them worked. However, when I use...
Hi,
I use nRF5 SDK v15.0.0. In my application I need periodically disable and enable Bluetooth because they are wifi also, which connected to the same antenna. Its mean...
Hi,
I'm trying send me the mac address of the device by UART by the following method:
By serial I receive:
Start b9:24:82:d5:4f:81
The problem its that the device...
Good day
Firstly, an overview.
I am currently busy with a technical proposal for a client. Initial details will result in a completed approx 60 000+ sensor network. My...
Hi EveryBody!
I've begin to work with the n51 family, my board is based on a n51822QFAA H1 IC.
I use Keil5 MDK and a ST-Link V2 programmer. They work fine as I've tested...
IOS, nRF Toolbox 4.4.4, DFU Library version 4.1.1
Attempting to flash to ruuvi with nRF52832 reports
:INFO:Hash failure and
:INFO:Return false in CRC
to J-Link RTT...
Hi,
I'm trying to modify the slave latency and supervisory timeout setting, but found sometimes the gap_params_init() will get error after changing.
For example, I can...
I want to implement mesh functionality. There is no problem with nrf52dk board, but I think there is a problem with board that I made with nrf52832 chip. attach the photo...
I'm on SDK 15.2 and iOS 12 with nRF52832 on a custom board.
I've added the dfu service to my existing NUS/UART service. In the nRF connect app I can see both services and...
I have downloaded SDK software nRF5_SDK_15.2.0_9412b96. I am using segger studio as my IDE on windows.
I tried compiling the Example code for SAADC. There were no errors...
Hi, On SDK12.3 when using sd_flash_write at any memory location causes the device to halt and restart. On SDK11 I've been using flash_word_write and flash_page_erase using...
Hi I am using a nrf52832 board with a BMI160 sensor. I am trying to sample Accel and Gyro at 1600hz using a timer. The timer timeout is set at 20 ticks (32768/1600) @32768...
