Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello, I am facing an issue in nrf52dk (nrf52832dk). Whenever I access i2c0 bus for the controller it works fine but whenever i switched on the i2c1, it starts giving me device...
Hi, I`m working on a custom board. I have been playing around with it for a couple of months, but just recently stumble upon a strange behavior. This is a custom device where...
Hi, I am trying to use the external flash on the nRF54L15 DK with QSPI to perform the zephyr/samples/subsys/fs/fs_sample sample.
I am using NCS v3.1.0 (on Windows if that...
I’m working on a project using the nRF54L15 SoC together with the nPM1300 Power Management IC . In my hardware setup:
BUCK2 output from the nPM1300 is connected to the...
I currently evaluated the use of the "<modem/at_parser.h>" (at_parser module).
Using it with the at-cmd "at+CEINFO?" is very irritating.
I 07.324 : CEINFO: +CEINFO: 0...
Our team is transitioning to the nRF Connect SDK after extensive experience with older nRF SDKs and custom build systems (based on cmake + west + python) integrated with VS...
I would like to know if in mesh device for the comuniation are used all that channel or only the 3 channel that are used for the advertising channel or all the channel 37...
Hi
any one a clue why I see this bar twice?(see attached picture)
Some thing probably went wrong with my previous older installation.
I already reinstaled Wireshark...
I'd like to call a function on the peripheral (by pressing a button or sending a command from the terminal) that performs unbonding from a central. I'm able to bond using...
We are looking to migrate our nrf52833 project to latest toolchain and SDK for build in visual studio.
We use MCU boot, BLE and Zephyr RTOS.
Do we need to follow each...
Hello,
i'm facing errors when trying to build matter sample thermostat.
I doesn't matter if i use VS Code or terminal
(v3.1.1) C:\ncs\v3.1.1\nrf\samples\matter\thermostat...
Dear Nordic Supportteam,
starting from the ESB sample I have developed a transmitter and a receiver application, both running on a separate nRF54L15DK. My goal is to find...
Hello, I am having a problem with Exercise 1 of the Cellular IoT lessons (nRF Academy, Asset Tracker Example). I have carefully followed all the steps outlined in the documentation...
Hi
I experienced higher sleep consumption after enabling CONFIG_PM_DEVICE. I reduced the project to the minimum and it seems that the combination of an enabled uart and...
Hi! I started designing a PCB for the nRF54L15 radio chip, which I intend to use for ESB communication between two relatively close-together (<10 meters) devices. I've been...
