Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
I was using an SPI serial nor flash device with NCS 2.8.0. I tried to get the flash into deep power down mode, but it doesn't seem to work well with NCS 2.8.0. So I upgraded...
Similar to ticket # 349557, we plan to operate nRF9151 in SLM mode and use both LTE and GNSS features. There is some interest in having GNSS (NMEA) data sent out on a dedicated...
Hi Team,
We have started our BLE development using nRF54L15 using SDK 3.1.0.
We have selected this MCU because it support all security features, we are going to start...
NFC certification and library.
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrfxlib/nfc/README.html tells me, NFC is supported by nrf52 and 53.
e.g. libnfct2t_nrf52...
I am using nrf54l15 with NCS v3.1.0 with the following error when i connect it(i worked in NCS v2.9.1 successfully):
Controller unresponsive, command opcode 0x2035 timeout...
We as a company love the app (nRF Connect) and use it accross a lot of devices to recover stolen goods with BLE.
However, on all my Android devices (modern tablets and phones...
I am working with St7789v driver based RGB565 Display . I have chosen SPI21 configured at 8Mhz and if I send 15 bytes chunk of image bitmaps, I can see the image in the display...
Hello, I am testing the system off demo on the nRF54L15 DK using nRF Connect SDK v2.8.0 (Zephyr v3.7.99). I ran the sample exactly as provided in the SDK .
Observed log...
I am using the nRF7002DK with the nRF5340 SoC. By default the board runs at 1.8 V until I provide 3.3 V on VIOREF. Currently, I am using another board just to drive VIOREF...
Hello there,
we're using multiple pwm-channels of one module of the nRF54L15 for different purposes (multiple motors, h-bridge control; depending on the project).
When...
Can my Power Profiler 2 be faulty?
It does the following in both source meter and ampere meter mode. I start to measure and it shows some microamps current that's expected...
I have a custom board that consists of a nRF52840 and a nRF7002 WiFi companion chip, connected via SPI. (not QSPI)
I wrote a tiny test program that configures the nRF7002...
I'm implementing an OAUTH procedure on my device. I'm able to access login.microsoftonline.com and get user and device codes, then after authorizing, I can access the token...
